Husqvarna F2201V1 Owner'S Manual Download Page 24

Page: 24 / 158

6 CONTROLS

6.14

Plug-in stand (FC 350 EU, FC 350 US)

H02629-10

The support for plug-in stand

is the left side of the wheel

spindle.
The plug-in stand is used to park the motorcycle.
The plug-in stand is used as a fork locker when transporting the
motorcycle.

Info

Remove the plug-in stand before riding.
The tool can be attached to the plug-in stand holders.

6.15

Side stand (FX 350)

401943-10

The side stand

is located on the left of the vehicle.

401944-10

The side stand is used for parking the motorcycle.

Info

When you are riding, side stand

must be folded up

and secured with rubber strap

6.16

Service hour counter

V01363-10

The service hour counter

is fitted in front of the handlebar.

It shows the total number of service hours of the engine.
The service hour counter begins counting when the engine is
started and stops when the engine is switched off.

Info

The value indicated by the service hour counter cannot be
cleared or adjusted.

Summary of Contents for F2201V1































































































































































Search results

Summary of Contents for F2201V1

Reviews:

Related manuals for F2201V1

Brands by name

Popular brands

Husqvarna F2201V1, Owner'S Manual

Search results

Summary of Contents for F2201V1

Reviews:

Related manuals for F2201V1

Brands by name

Popular brands