Husqvarna DS 700 Operator'S Manual Download Page 14

Page: 14 / 24

• If the anchor method is used to secure the machine,

locate the anchor at the proper distance from the hole

to be drilled (cored).

WARNING!

Machine must be held securely to prevent injury

to operator or damage to machine!
Always anchor machine properly before drilling!

Anchors shall only be used if the material being

drilled has the mechanical strength required to

hold the anchor. Use the proper Anchor for the

material.

DO NOT use vacuum system to secure machine

to a wall (horizontal drilling) or a ceiling!
Use ONLY anchor bolts to secure the machine to

a wall or ceiling!

Secure Drill Stand to Concrete Anchor with Anchor

Bolt (U) Through Anchor Bolt Slot (V).

Angle Bracket Assembly (T) (DS 700 / DS 800)

Angle Bracket Accessory (S) (DS 800)

(A2)

(A1 / A2)

• As a minimum, use a 5/8” or M16 expansion-type

anchor (not supplied) that will accept a 5/8” or M16

threaded rod or bolt to secure the machine base to

the work surface.

• Install concrete anchor per the manufactures instruc-

tions and verify that it is securely held in place. For

more information on concrete anchors, contact the

Concrete Anchor Manufacturers’ Association at

www.

concreteanchors.org.

• Secure the drill stand base to the surface using a

5/8” or M16 Capscrew and Washer (U) (hardware

per anchor manufactures instructions) through the

Anchor Bolt Mounting Slot (V). Securely tighten the

mounting hardware (U) per the anchor manufactures

instructions.

Angle Drilling:

• This drill stand, as supplied, will only drill (core) holes

90 degrees to the mounting surface. Accessory items

can be fitted to the machine to allow drilling at an angle

to the mounting surface.

Angle Bracket Assembly

(DS 700 & DS 800)

The addition of this accessory will allow the drill stand

to tilt backwards (toward wheels) at up to a 45 degree

angle. Use the DS 700 / DS 800 spare parts list to de-

termine the correct part number for this accessory.

Angle Bracket (Column to Base)

(DS 800 Only)

The addition of this accessory will allow the DS 800

drill stand (not available for DS 700) to tilt backwards

(toward wheels) to approximately a 90 degree angle

from the mounting surface. Use the DS 700 / DS 800

spare parts list to determine the correct part number for

this accessory.

MACHINE SET-UP

Summary of Contents for DS 700

























Search results

Summary of Contents for DS 700

Reviews:

Related manuals for DS 700

Brands by name

Popular brands

Husqvarna DS 700, Operator'S Manual

Search results

Summary of Contents for DS 700

Reviews:

Related manuals for DS 700

Brands by name

Popular brands