Husqvarna DMT 700 Operator'S Manual Download Page 39

Page: 39 / 48

English

– 39

TROUBLESHOOTING

Error messages

Fault
Code

Message on
the display

DTC description

Indication on the machine

Possible action

U100087

I/O Controller

No CAN
communication

Engine can not be started. No
machine function can be controlled.

Check damage to connectors X1, X4,
X14 and chassis harness. If found,
repair and restart system, reset fault
code.

If problem still exists, contact your
service agent for further information.

U100088

I/O Controller

Software download
failed

Contact your service agent.

P060745

IOC MPU

Program memory
failure

Contact your service agent for further
information.

P060742

IOC MPU

General memory
failure

C1F0612

Crank signal

Circuit short to
battery

Engine can not be started.

Check damage to key switch, key switch
connectors X30, X32 and harness. If
found, repair and restart system, reset
fault code.

C1E0111

Blade depth
sensor signal

Circuit short to
ground

Blade depth can not be displayed.
Blade depth stop can not be used.

Disconnect sensor and reset fault code.
If fault code no longer exists check
sensor and sensor harness.

Check damage to X13 and X14
connectors and harness to sensors. If
found, repair and restart system, reset
fault codes.

Contact your service agent for further
information.

C1E0112

Blade depth
sensor signal

Circuit short to
battery

C1D0115

Starter

Circuit short to
battery or open

Engine starter can not be controlled.
Cutting can not continue.

Check damage to X14 and X1
connector and harness. If found, repair
and restart system, reset fault code.

It problem still exists, contact your
service agent for further information.

C1D0111

Starter

Circuit short to
ground

Engine can not be started.

C1D0711

Power supply
external device

Circuit short to
ground

Cutting can not continue.

Check cables to:

Blade depth sensor and sensor itself

E-track position sensor and sensor itself

Neutral start switch and switch itself

Lower/raise switch and switch itself

Water safety switch and switch itself

C1D0712

Power supply
external device

Circuit short to
battery

May not be able to read sensor
values.

C1D0815

AUX1

Circuit short to
battery or open

AUX1 can not be controlled by the
HMI.

Check K4 relay in relay/fuse box.

Check damage to X14 connector,
harness to relay/fuse box and relay/fuse
box connector. If found, repair and
restart system, reset fault code.

If problem still exists, contact your
service agent for further information.

C1D0811

AUX1

Circuit short to
ground

C1D0215

AUX2

Circuit short to
battery or open

AUX2 (5th wheel) can not be
controlled by the HMI.

Check K5 relay in relay/fuse box.

Check damage to X14 connector,
harness to relay/fuse box and relay/fuse
box connector. If found, repair and
restart system, reset fault code.

If problem still exists, contact your
service agent for further information.

C1D0211

AUX2

Circuit short to
ground

C1D0315

Blade clutch

Circuit short to
battery or open

Blade clutch can not be controlled by
the HMI. Blade might be engaged or
disengaged the whole time.

Check K7 in relay/fuse box.

Summary of Contents for DMT 700

















































Search results

Summary of Contents for DMT 700

Reviews:

Related manuals for DMT 700

Brands by name

Popular brands

Husqvarna DMT 700, Operator'S Manual

Search results

Summary of Contents for DMT 700

Reviews:

Related manuals for DMT 700

Brands by name

Popular brands