Husqvarna 524 L Operator'S Manual Download Page 26 | Manualshive

Page: 26 / 36

background image

MAINTENANCE

26 – English

Cleaning the air filter

Close the choke valve by moving the choke control up.

Remove the air filter cover and take out the filter. Wash it
clean in warm, soapy water. Clean also the inside of the
filter cover by using air or a brush. Ensure that the filter is
dry before refitting it.

Remove the Felt filter from the filter holder and gently
brush debris from the filter. Check the rubber sealing
surface. Change the filter on the rubber seal if damaged.

An air filter that has been in use for a long time cannot be
cleaned completely. The filter must therefore be replaced
with a new one at regular intervals.

A damaged air filter

must always be replaced.

Damaged, very dirty, or fuel-

soaked air filter must always be replaced.

Bevel gear

The bevel gear is filled with the right quantity of grease at
the factory. However, before using the machine you
should check that the bevel gear is filled three-quarters
full with grease. Use HUSQVARNA special grease.

The grease in the bevel gear does not normally need to
be changed except if repairs are carried out.

H1155734-26,524L,525LST,RJD,.fm Page 26 Friday, March 8, 2013 7:19 AM

«
...
24
25
26
27
28
...
»

Summary of Contents for 524 L





































Reviews:

No comments

Related manuals for 524 L

Brand: Echo Pages: 28

Brand: Echo Pages: 52

Gardenline YGL N.G. 51/2

Brand: Zgonc Pages: 36

Brand: Black + Decker Pages: 124

Brand: Powermate Pages: 72

Brand: Leviton Pages: 2

Brand: VETRO Pages: 48

Brand: Winton Pages: 40

Brand: Bushranger Pages: 20

Brand: Yard force Pages: 4

Brand: Daga Pages: 28

Grass trimmer/edger

Brand: Yardworks Pages: 24

Brand: Ozito Pages: 6

Brand: Zenoah Pages: 16

Brand: Tanaka Pages: 16

POWERPLUS POWEG4010

Brand: VARO Pages: 8

Brand: Garland Pages: 156

AL-Dimmer-1 PRO

Brand: Acclaim Lighting Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands