manualshive.com logo in svg

Husqvarna 5000, Operator'S Manual, Page: 16 / 18

Share
Download
Husqvarna 5000 Operator'S Manual Download Page 16

16

TECHNICAL SPECIFICATIONS

Weight and Dimensions  5000

Weight – dry    

 

 

 

 

507 lbs  

 

230 kg

Weight with gasoline and oil full   

 

 

531 lbs  

 

241 kg

Length   

 

 

 

 

 

59 inch  

 

1499 mm

Width   

 

 

 

 

 

30 inch  

 

762 mm

Height   

 

 

 

 

 

38 inch  

 

965 mm

Blade

Material cut 

 

 

 

 

 

Green concrete only

Blade type 

 

 

 

 

 

14.0” (355 mm) or 12.0” (305 mm) dry cut with tri-arbor

Blade rotation   

 

 

 

 

Counter clockwise, upcutting

Blade shaft speed 

 

 

 

 

2750 rpm

Cutting depth   

 

 

 

 

4 inch maximum (101 mm) depending on blade size and   

 

 

 

 

 

 

 

amount of blade wear

Cutting distance from wall 

 

 

 

3 1/2 inch 

 

89 mm

Average cutting rate - Estimate only. Speed will vary with job conditions and concrete mixes.

 

 

 

 

 

 

 

 

 

 

4 inch (101 mm) depth  

3 inch (76 mm) depth   

2 inch (51 mm) depth

Soft aggregates  

16 ft/min (4.9 m/min) 

 

24 ft/min (7.3 m/min) 

 

32 ft/min (9.8 m/min)

Medium aggregates 

12 ft/min (3.7 m/min) 

 

17 ft/min (5.2 m/min) 

 

22 ft/min (6.7 m/min)

Hard aggregates 

8 ft/min (2.5 m/min) 

 

10 ft/min (3.0 m/mim)   

12 ft/min (3.7 m/min)

 

Blades are available in 14.0 inch (355 mm) and 12 inch (305 mm) diameters and in 0.100 inch (2.5 mm), 

 

0.250 inch (6.4 mm), 0.380 inch (9.7 mm), and 0.500 inch (12.7 mm) widths

Engine:

 

 

 

 

 

 

Kohler Command Pro CH740

Engine oil volume (with filter) 

 

 

 

2.1 quarts 

 

2.0 liters

Gasoline tank volume   

 

 

 

3.0 gal   

 

11 liters

Type   

 

 

 

 

 

Air cooled, 4-cycle, twin cylinder, hydraulic overhead

 

 

 

 

 

 

 

valves, gasoline engine

Air filter  

 

 

 

 

 

Tri phase remote mount canister style

Oil system 

 

 

 

 

 

Full pressure lubrication with spin-on oil filter

Muffler   

 

 

 

 

 

Low noise, side exhaust

Emissions 

 

 

 

 

 

Complies with EPA Phase 2 and CARB Tier II USA 

 

 

 

 

 

 

 

regulations

Cooling  

 

 

 

 

 

Air cooled

Cylinder 

 

 

 

 

 

Aluminum with cast iron liner

Controls 

 

 

 

 

 

Instrument panel mounted manual choke, electric switch 

 

 

 

 

 

 

 

operated throttle, keyed on/off switch

CALIFORNIA AIR RESOURCES BOARD (CARB): 

This machine is considered to be construction equipment 

with engine power equal or greater than 

1

9KW (

25

hp), CARB standards do not apply to this machine. 

For more information see the website 

http://www.arb.ca.gov/msprog/offroad/preempt.htm

CONFORMITY CERTIFICATES

Summary of Contents for 5000



















Reviews:

No comments