manualshive.com logo in svg

Husqvarna 5000, Operator'S Manual, Page: 15 / 18

Share
Download
Husqvarna 5000 Operator'S Manual Download Page 15

15

TROUBLESHOOTING

ENGINE RUNS ROUGH, BACK FIRES OR CAN NOT 

REACH FULL SPEED

 

- Check if there is fuel in the tank and it is the correct fuel.  

  Make sure there is no water in the fuel.

- Check that the spark plugs are clean and properly gapped.

- Check that choke is in the “off” position after engine is warm.

- Check that air filter is not dirty or plugged.

- Check that the throttle lever is properly set.

ENGINE WILL NOT START

 

- Check that the red emergency stop button is pulled up.

- Check if there is fuel in the tank and it is the correct fuel.  

  Make sure there is no water in the fuel.

- Check that the spark plug wires are connected to the spark  

  plugs.

- Engine is flooded. Adjust the choke per the engine owner’s  

  manual.

- Check that the air filter is not dirty or plugged.

- Check the choke is in the “on” position for cold starts. Adjust  

  the choke per the engine owner’s manual.

- Check that the blade shaft rotates freely and no concrete has  

  built up in the blade block.

SAW PULLS TO ONE SIDE WHILE SAWING

 

- Check front and rear guide is properly aligned with the center  

  of the diamond blade.

- Check to see if diamond blade is worn out, glazed, warped or  

  damaged.

- Do not twist or move the saw sideways while cutting. Make  

  gradual changes in pressure on the handlebar to control the  

  saw in the cut.

- Insure that all wheels rolls freely and smoothly.

- Do not force the saw. Allow the diamond blade to cut at its  

  own rate of speed.

- Check the skid plate for damage or burrs.

- Insure both driver gears are contacting the rear wheel gears, 

  all gears and rear wheels are clean and not damaged.  

SAW IS SPALLING AND RAVELLING CUT

 

- Check to see if the diamond blade is worn out, glazed,  

  warped or damaged.

- Insure skid plate moves freely up and down the entire shaft  

  length without contacting the diamond blade.

- Check skid plate for excessive wear or gap around the  

  diamond blade.

- Check skid plate for tension or loose mounts. Skid plates are    

  preset at the factory.

- Check bottom of skid plate for metal burrs or irregularities.

- Insure skid plate is not twisted or bent.

- Check lexan covers for free movement up and down.

- Insure there is spring down pressure at each end of the skid  

  plate.

- Do not twist or move the saw sideways while cutting.

- Check that the engine is running properly and at full throttle.

- Check belt and belt idler for proper tension.

- Insure the diamond blade is properly mounted and secured  

  with clean flanges.

- Insure that the diamond blade is the correct specification for  

  your area.

- Insure the slab is in clean with no debris that could raise the  

  skid plate or saw while cutting.

- Use Husqvarna joint protectors at all cut intersections.

- Clean excess concrete debris from the blade block assembly.

- Check that the scrapers in the blade block are not bent or  

  binding.

- Insure that the blade block shafts are not bent or damaged.

- Check that the front diverter in the blade block is not bent and  

  the diverter legs are not contacting the concrete.

Summary of Contents for 5000



















Reviews:

No comments