background image

FUEL HANDLING

12 – English

Mixing

Always mix the gasoline and oil in a clean container 
intended for fuel.

Always start by filling half the amount of the gasoline 
to be used. Then add the entire amount of oil. Mix 
(shake) the fuel mixture. Add the remaining amount of 
gasoline.

Mix (shake) the fuel mixture thoroughly before filling 
the machine’s fuel tank.

Do not mix more than one month’s supply of fuel at a 
time.

If the machine is not used for some time the fuel tank 
should be emptied and cleaned.

Fueling

Clean the area around the fuel cap. Contamination in 
the tank can cause operating problems.

Ensure that the fuel is well mixed by shaking the 
container before filling the tank.

!

WARNING! Taking the following 
precautions, will lessen the risk of fire:

Do not smoke or place hot objects near 
fuel.

Always shut off the engine before 
refuelling.

Always stop the engine and let it cool for 
a few minutes before refuelling.

When refuelling, open the fuel cap slowly 
so that any excess pressure is released 
gently.

Tighten the fuel cap carefully after 
refuelling.

Always move the machine away from the 
refuelling area before starting.

H1153175-95,426Ex,US.fm  Page 12  Monday, November 30, 2009  11:20 AM

Summary of Contents for 426EX

























Reviews: