manualshive.com logo in svg

Husqvarna 362D28, Operator'S Manual, Page: 3 / 20

Share
Download
Husqvarna 362D28 Operator'S Manual Download Page 3

English - 3

Warning labels on the machine

(1)

(2)

(4)

(5)

(1)   Read the operator’s manual carefully and 

make sure you understand the instructions 

before using the machine.

(2)   Wear a protective mask, eye and ear 

protection.

(3)   Wear foot protection.

(4)   Wear gloves.

(5)   WARNING! The machine can be a 

dangerous tool if used incorrectly or 

carelessly, which can cause serious or fatal 

injury to the operator or others.

Symbols on the machine

The port to refuel the “MIX 

GASOLINE” 

Position: 

FUEL TANK CAP

The direction to open the choke

Position: 

CARBURETTOR BODY

(3)

For safe operation and maintenance, symbols 

are carved in relief on the machine. According 

to these indications, be careful not to make a 

mistake.

 IMPORTANT

If the warning label peels off or becomes soiled 

and impossible to read, you should contact the 

dealer from which you purchased the product to 

order new labels and affix them in the required 

location(s).

What is what?

(1) Flexible hose 

(2) Clamp

(3) Wire

(4) Joint

(5) Straight pipe

(6) Bent pipe

H1152413-26,362D28,GB.indd   3

2009-10-15   15.58

Summary of Contents for 362D28





















Reviews:

No comments