manualshive.com logo in svg

Husqvarna 362D28, Operator'S Manual, Page: 17 / 20

Share
Download
Husqvarna 362D28 Operator'S Manual Download Page 17

English - 17

1.  Remove the muffler, insert a screwdriver into the 

vent, and wipe away any carbon buildup. Wipe 

away any carbon buildup on the muffler exhaust 

vent and cylinder exhaust port at the same time.

2.  Tighten all screws, bolts, and fittings.

3.  Check to see if any oil or grease has worked its 

way in between the clutch lining and drum, and 

if it has, wipe it away using oil-free, lead-free 

gasoline.

■

  AIR INLET NET

  IMPORTANT

•  Blowing air is taken in from the air inlet net. 

When air flow has dropped down during 

operation, stop the engine and inspect the air 

inlet net for blocking by obstacles.

•  Note that failure to remove any such obstacles 

may result in the engine becoming overheated 

and damaged.

 WARNING

 

Never use the blower without the net of the 
machine. Before each use, check that the 
net is attached in place and is free from any 
damage. 

■

  SHOULDER STRAP

•  If the shoulder strap is damaged it may break 

during use, thus causing the product to fall 

and resulting in personal injury. Follow the 

instructions below to replace the shoulder strap 

with new one.

1.  Pass the upper end of the strap through the 

hanger, making the FLAPPED SIDE OUTSIDE.

2.  Put the end of the strap through the ring on the 

strap, and then push the ring toward the hanger 

as close as possible.

Maintenance

(1)Ring

(2)Flapped side

 WARNING

 

The flap on the end of the strap works as 
a stopper. Never install the strap with the 
flapped side inside, or the unit may fall from 
the operation, which could result in injury to 
the operator and/or damage to the unit.

■

 SPRAY DEVICE

  IMPORTANT

 •  As fertilizers are easy to absorb moisture, left 

behind fertilizers will cause error for the 
shutter operation.  After spraying fertilizers, 
clean the spray device carefully.

 •  Correct length of the chemical tank locking 

hooks is 45-46mm.  Shorter hooks than this 
cause excess fixing forces and may end up 
with deformation or breakage of related 
components. Longer hooks cause insufficient 
contact of the tank and chemicals may leak. 

 •  For long time storage of the sprayer, leave the 

chemical tank cap loose. Otherwise, a cap 
gasket may be deformed. 

(1)Air inlet net

H1152413-26,362D28,GB.indd   17

2009-10-15   15.58

Summary of Contents for 362D28





















Reviews:

No comments