background image

 

GENERAL SAFETY PRECA

 

UTIONS

 

6

 

 – 

 

English

 

Bef

 

ore using a new chain saw

 

 

Please read this manual carefully.

Check that the cutting equipment is correctly fitted 
and adjusted. See instructions under the heading 
Assembly.

Refuel and start the chain saw. See the instructions 
under the headings Fuel Handling and Starting and 
Stopping.

Do not use the chain saw until sufficient chain oil has 
reached the chain. See instructions under the 
heading Lubricating cutting equipment.

Long-term exposure to noise can result in permanent 
hearing impairment. So always use approved hearing 
protection.

 

Impor

 

tant

!

 

W

 

ARNING! Under no circumstances may 

the design of the machine be modified 
without the permission of the 
manufacturer. Always use genuine 
accessories. Non-authorized 
modifications and/or accessories can 
result in serious personal injury or the 
death of the operator or others.

!

 

W

 

ARNING! A chain saw is a dangerous 

tool if used carelessly or incorrectly and 
can cause serious, even fatal injuries. It is 
very important that you read and 
understand the contents of this operator’s 
manual.

!

 

W

 

ARNING! The inside of the muffler 

contain chemicals that may be 
carcinogenic. Avoid contact with these 
elements in the event of a damaged 
muffler.

!

 

W

 

ARNING! Long term inhalation of the 

engine’s exhaust fumes, chain oil mist 
and dust from sawdust can represent a 
health risk.

!

 

W

 

ARNING! This machine produces an 

electromagnetic field during operation. 
This field may under some 
circumstances interfere with active or 
passive medical implants. To reduce the 
risk of serious or fatal injury, we 
recommend persons with medical 
implants to consult their physician and 
the medical implant manufacturer before 
operating this machine.

!

 

W

 

ARNING! Never allow children to use or 

be in the vicinity of the machine. As the 
machine is equipped with a spring-
loaded stop switch and can be started by 
low speed and force on the starter 
handle, even small children under some 
circumstances can produce the force 
necessary to start the machine. This can 
mean a risk of serious personal injury. 
Therefore remove the spark plug cap 
when the machine is not under close 
supervision.

 

IMPOR

 

TANT!

This chain saw for forest service is designed for forest 
work such as felling, delimbing and cutting.

You should only use the saw with the bar and chain 
combinations we recommend in the chapter Technical 
data.

Never use the machine if you are fatigued, while under 
the influence of alcohol or drugs, medication or anything 
that could affect your vision, alertness, coordination or 
judgement.

Wear personal protective equipment. See instructions 
under the heading ”Personal protective equipment”.

Do not modify this product or use it if it appears to have 
been modified by others.

Never use a machine that is faulty. Carry out the checks, 
maintenance and service instructions described in this 
manual. Some maintenance and service measures must 
be carried out by trained and qualified specialists. See 
instructions under the heading Maintenance.

Never use any accessories other than those 
recommended in this manual. See instructions under the 
headings Cutting equipment and Technical data.

CAUTION! Always wear protective glasses or a face visor 
to reduce the risk of injury from thrown objects. A chain 
saw is capable of throwing objects, such as wood chips, 
small pieces of wood, etc, at great force. This can result 
in serious injury, especially to the eyes.

!

 

W

 

ARNING! Running an engine in a 

confined or badly ventilated area can 
result in death due to asphyxiation or 
carbon monoxide poisoning.

!

 

W

 

ARNING! Faulty cutting equipment or 

the wrong combination of bar and saw 
chain increases the risk of kickback! Only 
use the bar/saw chain combinations we 
recommend, and follow the filing 
instructions. See instructions under the 
heading Technical  data.

Summary of Contents for 345 E EPA II













































Reviews: