34
– English
Engine
Cylinder volume, cu.in/cm
3
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication system
Manufacturer
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at 9000 rpm, ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain, Lbs/kg
Chain/bar
Standard bar length, inches/cm
Recommended bar lengths, inches/cm
Usable cutting length, inches/cm
Chain speed at max. power, m/sec
Pitch, inch/mm
Thickness of drive link, inch/mm
Number of teeth on drive sprocket
TECHNICAL DATA
Guide bar
Saw chain
Length
Pitch
Max nose
inch
inch
radius
13
0,325"
10T
Husqvarna H30 or
15
0,325"
10T
Oregon 95VP
16
0,325"
10T
18
0,325"
10T
15
0,325"
10T
Husqvarna H25 / S24 or
16
0,325"
10T
Oregon 21BP / 34LG or 34SL
18
0,325"
10T
20
0,325"
12T
340
2,49/40,8
1,57/40
1,28/32
2 700
2,0/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
ZAMA
C3-EL18
1,05/0,5
9
0,53/0,25
Automatic
10,3/4,7
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"/1,6
7
345
2,75/45,0
1,65/42
1,28/32
2 700
2,2/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
ZAMA
C3-EL18
1,05/0,5
9
0,53/0,25
Automatic
10,3/4,7
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"/1,6
7
350
3,15/51,7
1,77/45
1,28/32
2 700
2,3/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
ZAMA
C3-EL18
1,05/0,5
5-12
0,55/0,26
Automatic
10,6/4,8
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"1,6
7
0,050"/1,3 mm
H30/95VP
20BP
33LG
33SL
0,058"/1,5 mm
–
H25/21BP
34LG
34SL
0,063"/1,6 mm
–
22BP
35LG
35SL
Note:
For the chains above you are free to choose between 0,050",
0,058 and 0,063" gauge drive link for the corresponding bar, see
table below.
The following is a list of recommended cutting equipment for
Class 1A and 1B Chainsaws.
The combinations of powerhead, bar and chain meet all
requirements outlined in the CSA Z62.1-95 Chainsaws and
Z62.3-96 Chainsaw Kickback standards.
The guide bar nose radius is determined by either the
maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a solid bar.
As we are listing the maximum guide bar nose radius, you
may use a guide bar with smaller nose radius than in our list.
For guide bars of the same length, all sprocket-nose guide
bars of the same pitch and having the same number of
sprocket teeth may be considered to have equivalent kick-
back energy.
A hard nose bar having the same length and nose radius as a
sprocket-nose bar may be considered to have equivalent or
less kickback energy than the sprocket-nose bar.
We recommend that you as replacement use the listed bars
and chains or ”Type C Low-Kickback Saw Chains” which are
available at your dealer.
RECOMMENDED CUTTING EQUIPMENT
FOR CANADA
