Husqvarna 288XP Lite Operator'S Manual Download | Manualshive

Page: 4 / 36

background image

4

– English

!

!

CHAIN SAW SAFETY EQUIPMENT

This section explains the various safety features of the saw,
how they work, and basic inspection and maintenance you
should carry out to ensure safe operation. (See the

”What is

what?” section to find out where these components are on Your
saw).

NEVER USE A CHAIN SAW THAT HAS
FAULTY SAFETY EQUIPMENT! Carry out the
inspection, maintenance and service routines
listed in this section.

1

Chain brake and front
hand guard

2

Throttle lock

3

Chain catcher

4

Right hand guard

5

Vibration damping system

6

Stop switch

7

Muffler

8

Cutting equipment (see
”Cutting equipment”
section).

SAFETY INSTRUCTIONS

!

A chain saw is a dangerous tool if used
carelessly or incorrectly and can cause
serious, even fatal injuries. It is very important
that you read and understand these
instructions.

PERSONAL PROTECTIVE EQUIPMENT

MOST CHAIN SAW ACCIDENTS HAPPEN
WHEN THE CHAIN TOUCHES THE OPERA-
TOR. You must wear approved protective
equipment whenever you use a chain saw.
Personal protective equipment cannot
eliminate the risk of injury but it will reduce
the degree of injury if an accident does
happen. Ask your chain saw dealer for help in
choosing the right equipment.

• PROTECTIVE HELMET
• HEARING PROTECTION
• PROTECTIVE GLASSES

OR VISOR

• GLOVES WITH

SAW PROTECTION

• PROTECTIVE TROUSERS

WITH SAW PROTECTION

• BOOTS WITH SAW

PROTECTION, STEEL
TOE-CAP AND NON-SLIP
SOLE

Generally clothes should be
close-fitting without restricting
your freedom of movement.

• ALWAYS HAVE A FIRST

AID KIT NEARBY

«
...
2
3
4
5
6
...
»

Summary of Contents for 288XP Lite





































Reviews:

No comments

Related manuals for 288XP Lite

Brand: ICS Pages: 26

PE-AKS 18 Li Basic

Brand: Pattfield Pages: 200

Brand: Remington Pages: 57

Brand: GARDEO PRO Pages: 173

Brand: SNOWJOE Pages: 20

Brand: Homelite Pages: 32

Motosierra de 50 cm (20 pulg.)

Brand: Homelite Pages: 120

Brand: Homelite Pages: 428

Brand: Kobalt Pages: 33

Quickvent QV-6700 Type 1

Brand: Echo Pages: 30

Brand: Yard force Pages: 19

Brand: Zenoah Pages: 148

Brand: Raider Pages: 70

Brand: Gardenline Pages: 44

Brand: LAWN STAR Pages: 19

CS-3000 TYPE 1E - SERIAL NUMBER 2994 - 4033

Brand: Echo Pages: 24

Brand: HART Pages: 80

Brand: Husqvarna Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands