Husqvarna 261 Operator'S Manual Download Page 27 | Manualshive

Page: 27 / 36

background image

English –

27

!

Fuelling

Taking the following precautions, will lessen
the risk of fire.

• Do not smoke or place warm objects in the vicinity of

the fuel.

• Always shut off the engine before refuelling.
• Slowly open the fuel cap, when filling fuel, so that

possible overpressure is slowly released.

• Tighten the fuel cap carefully after fuelling.
• Always move the saw from the fuelling area before

starting.

Clean around the fuel cap.
Clean the fuel and chain oil
tanks regularly. The fuel filter
should be changed at least
once a year. Contamination in
the fuel tanks causes
malfunction. Make sure the
fuel is well mixed by shaking
the container before fuelling.
The volume of chain oil and
fuel tanks are adjusted to
each other. Therefore, always
fill chain oil and fuel at the
same time.

FUEL HANDLING

Min 3 m
(10ft)

«
...
25
26
27
28
29
...
»

Summary of Contents for 261





































Reviews:

No comments

Related manuals for 261

Brand: Zenoah Pages: 48

Brand: Zenoah Pages: 58

Brand: Zenoah Pages: 4

Brand: Zenoah Pages: 19

Brand: Meec tools Pages: 132

Sunjoe 24V-X2-CS16-CT-RM

Brand: SNOWJOE Pages: 28

Brand: EGO Pages: 31

Brand: Echo Pages: 60

Brand: ATIKA Pages: 2

Brand: ATIKA Pages: 6

Brand: EINHELL Expert Pages: 40

Brand: Yard force Pages: 20

Brand: STERWINS Pages: 365

Brand: Zenoah Pages: 7

Brand: GARDEO PRO Pages: 46

Brand: Makita Pages: 8

Brand: Stihl Pages: 112

Brand: Worx Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands