background image

4

PARTS PACKED SEPARATELY IN CARTON

(1) POWER CORD

(198563)

(1) DISCHARGE CHUTE

(3) RETAINER 

SPRINGS 

 (169675)

(6) SHEAR BOLTS 1/4-20 x 1-3/4

(192090)

(6) LOCKNUTS

1/4-20

(73800400)

EXTRA SHEAR BOLTS AND NUTS

(1) WASHER 3/8

(19131316)

(1) LOCKNUT 3/8

(73800600)

ROTATOR HEAD MOUNTING

(1) AUGER CONTROL ROD

(1) SAFTEY IGNITION KEY

(422663)

(1) MULTI-

WRENCH

(180684)

(2) FLAT WASHERS

(2) CARRIAGE BOLTS 

3/8-16 x 2.25

(2) HANDLE KNOBS

ASSEMBLY / PRE-OPERATION

HOW TO SET UP YOUR SNOW THROWER 

TOOL BOX (See Fig. 10)

A toolbox is provided on your snow thrower. The toolbox is 

located on top of the belt cover.  Store the extra shear bolts, 

nuts and multi-wrench provided in parts bag in the toolbox.

Read these instructions and this manual in its entirety 

before you attempt to assemble or operate your new 

snow thrower.  Reading the entire manual will familiar-

ize you with the unit, which will assist you in assembly, 

operation and maintenance of the product.

Your new snow thrower has been as sem bled at the factory 

with the ex cep tion of those parts left unassembled for ship-

ping purposes. All parts such as nuts, washers, bolts, etc., 

necessary to com plete the as sem bly have been placed in 

the parts bag. To ensure safe and proper operation of your 

snow thrower, all parts and hard ware you assemble must 

be tightened se cure ly. Use the correct tools as nec es sary 

to ensure proper tightness.

REMOVE SNOW THROWER FROM CAR TON

1.  Remove all accessible loose parts and parts boxes 

from carton.

2.  Cut down all four corners of carton and lay panels flat.
3.  Remove the two (2) screws securing the auger housing 

to the pallet.

4.  Remove all packing materials ex cept plastic tie holding 

speed control rod to lower handle.

5.  Remove the two (2) plastic ties securing the upper 

handle to the pallet.

6.  Remove snow thrower from carton and check carton 

thor ough ly for ad di tion al loose parts. 

Summary of Contents for 1827SB





















Reviews: