background image

25

(a)

Abrasion to mower decks;

(b)

Tires damaged by external punctures;

(c)

Natural discoloration of materials due to ultraviolet light;

(d)

Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures;

In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product related to or including
any of the following:

(e)

Failure to provide or perform required maintenance services as prescribed in the operator's manual;

(f)

Abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, use of unauthorized attachments, Lack of lubrication or

engine failure, due to the use of oils that do not meet Engine manufacturer's specifications;

(g)

Use of gasohol, containing methanol (wood alcohol). Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE

(methyl/tertiary/butyl/ether) is approved;

(h)

Use of ether or any starting fluids;

(i)

Pressure cleaning or steam cleaning the product;

(j)

Use of spark plugs other than those meeting emission performance requirements listed in the operator's manual;

(k)

Tampering with engine speed governor or emission components, or running engines above specified and recommended engine speeds as

listed in your operator's manual;

(l)

Operation of the unit with improperly installed/removed or modified cutting shields, guards, or safety devices;

(m) Any removed/damaged air filter, excessive dirt, abrasives, salt water, moisture, corrosion, rust, varnish, stale fuel, or any adverse reaction due

to incorrect storage procedures;

(n)

Failures due to improper set up, pre-delivery service or repair service by anyone other than an authorized Husqvarna servicing dealer during

the warranty period;

(o)

Dirt contaminated grease or oil, use of incorrect type of greases or oils, failure to comply with recommended greasing intervals, water or

moisture damage, and/or improper storage;

(p) Sprayers pumping or spraying caustic or flammable materials, lack of or broken strainers; or

(q) Continued use of product, after initial operational problem or failure occurs.

9.

Reinforced Stamped (Armor Protected) 10 Year Limited & Fabricated Limited Lifetime, Deck Warranties.

 These Limited Warranties are for

the deck shell only  mechanical components/parts such as belts, pulleys, spindle housings, bearings, blades, rods, height adjusters, caster/anti scalp
wheels

are NOT covered. The Limited Lifetime Warranty does not cover damage other than that resulting from defects in material or

workmanship. The following are NOT considered defects in material or workmanship, and therefore are NOT covered:

(a)

Abrasion to mower decks, including sand wear;

(b)  Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures;

(c)   Rust and corrosion; and

(d)  Natural discoloration of paint or other materials due to ultraviolet light.

HOW TO OBTAIN SERVICE

10.

Authorized Husqvarna Servicing Dealer/Center. 

In order to obtain warranty coverage it is your responsibility (at your expense) to deliver or ship

your Husqvarna unit to an authorized Husqvarna Servicing Dealer/Center and arrange for pick-up or return of your unit after the repairs have been made.
If you do not know the location of your nearest authorized Husqvarna Servicing Dealer, call Husqvarna, at 1-800-487-5951 during the hours of 8:00 AM
to 8:00 PM Eastern Standard Time, or visit 

www.husqvarna.com

. Should you require assistance or have questions concerning this Limited Warranty, you

may contact us at 800-487-5951 (US) or 800-805-5523 (Canada) during the hours of 8:00 AM to 8:00 PM Eastern Standard Time or contact us through
the web at www.husqvarna.com.

11.

Documentation Required. 

You must maintain and present Proof of purchase (including date, product model and, if applicable, engine serial

number) to an authorized Husqvarna Servicing Dealer for warranty service under this Limited Warranty. Proof of purchase rests solely with you.
Husqvarna encourages you to register your product online at 

www.usa.husqvarna.com

 (US & Canada) to help ensure, among other things, that you can

be notified of important product information. However, registering your product is not a condition of warranty service.

Husqvarna Professional Products, NA, 

Inc.

9335 Harris Corners Parkway, Suite 500, Charlotte, NC28269

575 49 43-01 W 2012 IR

Summary of Contents for 1650EXLT





























Reviews: