Husqvarna 1130SB-LSB Owner'S Manual Download Page 9

Page: 9 / 44

RECOIL

(AUXILIARY)

STARTER

HANDLE

THROTTLE

/ ENGINE

CONTROL

MUF FLER

GAS O LINE

FILLER CAP

SAFETY

IGNITION

KEY

CHOKE

CON-

TROL

ELECTRIC

START

BUTTON

PRIM ER

FUEL

SHUT-OFF

VALVE

OPERATION

Drive speed control lever -

used to select forward or

reverse motion and speed of snow thrower.

Traction drive control lever -

used to engage power-

pro pelled for ward or reverse motion of snow thrower.

LH and RH turn triggers -

used to steer the snow thrower.

Auger control lever -

used to engage auger motion (throw

snow).

Discharge chute control lever -

used to change the di-

rec tion the snow is thrown.

Skid plate -

used to adjust height of scraper bar from the

ground.

Drift cutter -

used to cut through deep snowdrifts.

Toolbox -

used to store spare shear bolts, locknuts and

wrench.

Safety ignition key -

must be inserted for the engine to

start and run. Remove when snow thrower is not in use.

Electric start button –

used for starting the engine.

Recoil (auxiliary) starter handle –

used for start ing the

en gine.

Primer -

pumps additional fuel from the carburetor to the

cylinder for use when starting a cold engine.

Throttle/engine control -

used to se lect either FAST or

SLOW engine speed and to STOP the engine.

Choke control -

used for starting a cold engine.

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

TRACTION

DRIVE

CONTROL

LEVER

DISCHARGE CHUTE CONTROL LEVER

DRIVE SPEED

CON TROL LEVER

AUGER

CONTROL

LEVER

MUF FLER

TOOLBOX

HANDLE

KNOB

SKID PLATE

CHUTE

DE FLEC TOR

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

FIG. 10

AU GERS

DISCHARGE

CHUTE

CLEAN-OUT TOOL

LIGHT

LH TURN

TRIGGER

DRIFT

CUTTER

DEFLECTOR

REMOTE

CONTROL

LEVER

Summary of Contents for 1130SB-LSB













































Search results

Summary of Contents for 1130SB-LSB

Reviews:

Related manuals for 1130SB-LSB

Brands by name

Popular brands

Husqvarna 1130SB-LSB, Owner'S Manual

Search results

Summary of Contents for 1130SB-LSB

Reviews:

Related manuals for 1130SB-LSB

Brands by name

Popular brands