Recommended Hookup
6-Sp
Manual de Instrucciones
Modelo F32/9032
Cómo usar la
Herramienta (Cont.)
8. Asegúrese de que el
gatillo y el elemento
de contacto de tra-
bajo (WCE) se mue-
van libremente
hacia arriba y hacia abajo sin
adherirse ni trabarse.
Servicio Técnico
Si desea hacer alguna pregunta refe-
rente a la reparación u operación de las
herramientas, o para solicitar copias
adicionales de este manual, sírvase lla-
mar a nuestro número especial, 1-877-
888-3872.
Sujetadores y Piezas de
Repuesto
Use solamente sujetadores originales
calibre 16 (o su equivalente) - (vea la
información sobre intercambio de
sujetadores). El desempeño de las
herramientas, la seguridad y la
duración pueden disminuir si no se
utilizan los sujetadores adecuados.
Cuando ordene piezas de repuesto o
sujetadores, especifique el número de
la pieza.
Para reparar la herramienta
La herramienta debe ser reparada
únicamente por personal calificado, y
deben usar piezas de repuesto y
accesorios originales Husky, o piezas y
accesorios que funcionen de manera
equivalente.
!
ADVERTENCIA
Para colocarle los sellos
Cada vez que repare una herramienta
deberá limpiarle y lubricarle las partes
internas. Le recomendamos que use
Parker O-lube o un lubricante equiva-
lente en todos los anillos en O. A cada
anillo en O se le debe dar un baño de
lubricante para anillos antes de instalar-
los. Igualmente, deberá ponerle un
poco de aceite a todas las piezas que se
mueven y muñones. Finalmente,
después de haberla ensamblado y antes
de probar la herramienta deberá
ponerle unas cuantas gotas de aceite
sin detergente 30W u otro aceite simi-
lar, en las líneas de aire.
3
General Safety
Information
(Continued)
Always assume the tool contains
fasteners. Respect the tool as a
working implement; no horseplay.
Always keep others at a safe dis-
tance from the work area in case of
accidental discharge of fasteners.
Do not point the tool toward your-
self or anyone whether it contains
fasteners or not. Accidental trigger-
ing of the tool could result in death
or serious personal injury.
Do not drive a fas-
tener on top of
other fasteners.
The fastener could
glance and cause
death or a serious
puncture wound.
Do not operate
or allow anyone
else to operate
the tool if any
warnings or
warning labels
are not legible. Warnings or warning
labels are located on the tool maga-
zine and body.
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, exam-
ine the tool closely for bent, cracked
or broken parts and air leaks. STOP
and repair before using or serious
injury could occur.
Caution indicates
a potentially haz-
ardous situation which, if not avoided,
MAY result in minor or moderate
injury.
Do not make any modifications to the
tool without first obtaining written
!
CAUTION
Standard B19.3-1991; Safety
Standard for Compressors for
Process Industries. Contact your air
compressor manufacturer for
information.
Operating The Tool
LUBRICATION
This tool requires lubrication before
using the tool for the first time and
before each use. If an inline oiler is
used, manual lubrication through the
air inlet is not required on a daily basis.
The work surface
can become dam-
aged by excessive lubrication. Proper
lubrication is the owner’s responsibil-
ity. Failure to lubricate the tool proper-
ly will dramatically shorten the life of
the tool and void the warranty.
1. Disconnect the
air supply from
the tool to add
lubricant.
2. Turn the tool so the
air inlet is facing up.
Place 4-5 drops of
30 W non-detergent
oil into air inlet. Do
not use detergent
oils, oil additives, or air tool oils. Air
tool oils contain solvents which will
damage the tool's internal compo-
nents.
NOTICE
approval from the manufacturer. Do
not use the tool if any shields or
guards are removed or altered. Do
not use the tool as a hammer.
Personal injury or tool
damage may occur.
Avoid long extended periods of
work with the tool. Stop using the
tool if you feel pain in hands or
arms.
Always check that the Work Contact
Element (WCE)
is operating
properly. A fas-
tener could acci-
dentally be dri-
ven if the WCE
is not working
properly.
Personal injury
may occur (See "Checking the Work
Contact Element" Section).
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the tool. Personal injury
may occur.
Notice indicates
important infor-
mation, that if not followed, MAY
cause damage to equipment.
Avoid using the tool when the mag-
azine is empty. Accelerated wear on
the tool may occur.
Clean and check all air supply hoses
and fittings before connecting the
tool to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
Air compressors providing air to the
tool should follow the requirements
established by the American
National Standards Institute
NOTICE
Model F32/9032
Operating Instructions
!
WARNING
Clavos - Información de intercambio
Los clavos usados con la F32/9032 también se pueden usar con las clavadoras : Bostitch T31-1, T29-30, BT-35, Duofast BB4440,
Hitachi NT45A , Paslode 2138-F18 , Porter Cable BN125, BN200, Sears 18309, y Senco SLP20, LS2, LS5.
Grapas - Información de intercambio
Las grapas usadas con la
F32/9032
también se pueden usar con las grapadoras: Senco LN4450, SJS-LR, SKS L11-15, Hitachi
N3804A, Duofast BN-1832S, KN-1848, ST-18, Stan-Tech SDS 18-14, Atro Minor 90/30, 90/32, 90/40, y Porter Cable NS100.
Sujetadores
movimiento
