PSU
01
Power Your Dream
PSU
Power Your Dream
02
APFC POWER
APFC POWER
Thank you for choosing this APFC
series
power
supply
unit
(
PSU
)!
Please
read
this
manual
carefully
and
follow
its
instructions
before
installation
.
APFC series is suitable
for
silence
seeker
.
It
uses
a
14cm
FAN
,
which
can reduce FAN
speed and low the noise. With dual & four +12V rails and high efficiency design
,
the
efficiency of APFC series power supply
can
reach
80%
at typical load
.
Active
power
factor
correction
circuit
which
inside
of
power
supply
can
also
reduce
power
loss
of
AC
input
line, PF value will get more than 0.99.
In
addition
we
'
ve included a variety of
industrial-grade protective circuitry: OCP
(
Over
Current
Protection
),
OPP
(
Over
Power
Protection
),
OVP
(
Over
Voltage
Protection
),
SCP
(
Short
Circuit
Protection
).
We would like to draw your attention to the conditions that your system works best for
you without failing. To avoid such failures and to increase lifetime of your entire system,
we suggest you to make sure that:
Your PC or server is not located near a radiator or any other heat producing device
Your PC or server is not located near a magnetic device
Your PC or server is not located in a moist or dusty or vibrating environment
Your PC or server is not exposed to direct sunshine
Your PC or server must be work at stable input AC voltage
Chapter A: Features
Complies with Intel ATX12V V2.2
(500
W
/600
W
)
and
EPS12V V2.91
(700
W
)
Supports Intel & AMD Dual
Core CPUs and
Multi
Core CPUs
;
SLI
ready
(500
W
)
Supports SLI & Crossfire Multi-GPU VGA card
(600
W
)
Active power factor correction
reduces
line
loss
and
power
distortion
Provides
dual +12V rails
(500
W
/600
W
);
four
+12
V
rails
(700
W
)
for stability and safety
Excellent
acoustic
&
thermal performance with Intelligent-Thermal Fan Control
Technology
Multiple protections: OCP,
OVP,
OPP,
SCP
100
%
Burn
-
In
tested
&
100% Hi-Pot tested
MTBF: 100,000 hours at 25
℃
User
'
s Manual
To make sure you connect your power supply properly, please check your
motherboard and graphic card manuals for compatibility before connecting
the power supply to any of your devices.
Chapter B: Installation
1. Turn off your computer
;
unplug
the
power
cord
from
your
old
power
supply
.
2. Open your computer case following your case manual.
3. Disconnect all PSU connectors from the motherboard and the peripherals,
such as cooler, HDD, DVD, CDR, FDD, etc.
4. Remove the old power supply from your computer case and install your new
power supply.
5. Connect the 20+4
pin main power connector to your motherboard.
Note
:
Use
the
separated
20
pin if your motherboard requires
20
pin power
connector.
6. Connect the Serial
-
ATA
connectors
to
the
peripherals
.
7. Connect the peripheral 4
pin power connectors if you are still using IDE hard
drives or optical drives.
8. Connect the PCI EXPRESS
power
connector
to
your
PCI
EXPRESS
graphic
card
.
9. Connect your cooler to the regular 4
pin
peripheral
connectors
if
you
have
.
10
.
Close
your
computer
case
and
connect
the
AC
power
cord
to
the
power
supply
.
Chapter C: Booting the system
1.Main power connector (20+4
pin
configuration
)
is
correctly
connected
.
2.CPU +12V power connector (4 or 4+4
pin
configuration
)
is
correctly
connected
.
3.PCIe
connector
(
if
required
by
GPU
)
is
correctly
connected
.
4.All other needed connectors are correctly connected.
Incorrect insertion might cause your PC unable to boot and some components
might be damaged!
5.AC cord is correctly connected to wall plug and
power
supply
AC
inlet
.
6.Then close your computer case.
7.Turn on the power supply by setting the I/O switch to
“
I
”
position
;
your
system
is
ready
to
run
.
8.Turn on your PC by pushing power button on your PC case!
Summary of Contents for APFC power
Page 1: ...APFC power...