background image

PAGE 15 

WARRANTY

All products are thoroughly tested to our Quality Control Procedures 

prior  to  leaving  our  manufacturing  facility.  Should  you  encounter 

a problem with your product, please notify us immediately upon 

receipt.  

Huntingdon  Fusion  Techniques  HFT

® 

warrants this product to be 

free of defects in workmanship and material, with exceptions stated 

below.

Warranty applies for normal and intended use of the product.

Huntingdon  Fusion  Techniques  HFT

®

 will not be held responsible 

for any incorrect use of the product.  

For  further  warranty  information,  please  refer  to  our  terms  and 

conditions.

All warranties shall not apply to any product or component which 

has been repaired or altered by anyone other than Huntingdon 

Fusion Techniques HFT

®

.

Huntingdon Fusion Techniques HFT

®

 shall not be liable for indirect, 

special, incidental or consequential damage or penalties and does 

not assume any liability of Purchaser, or to others, for injury to 

persons or property.

This warranty is in lieu of all other warranties, expressed and implied.

E&OE

Summary of Contents for Techweld MultiStrike TEG-1000

















Reviews: