Hunter IMMS-CI-HW Installation Instructions Manual Download Page 12

Page: 12 / 16

1. Connect only Hunter Clik-family sensors to IMMS. Refer to sensor

documentation for correct installation of sensor and permissible

wire runs.

2. Route sensor wires into the cabinet through low-voltage conduit,

and strip wire ends approximately

⁄

" (4.5 mm).

3. Connect one wire from sensor to “Sensor 1” position on upper

terminal strip.

4. Connect other sensor wire to “Sensor Common”.
5. Up to 3 sensors may be connected to the CI. Connect one wire from

each additional sensor to terminals “Sensor 2” and “Sensor 3”, and

connect the other wire from each sensor to the “Sensor Common”.

CONNECTION TO OPTIONAL CLIK SENSORS ....................................................................

POWERED SENSORS ..............................................................................................................

Hunter’s Wireless Rain-Clik™ and the Flow-Clik IMMS require 24VAC

power over their yellow wires.

��

�

��

�

��

�� 

�

��

Summary of Contents for IMMS-CI-HW

















Search results

Summary of Contents for IMMS-CI-HW

Reviews:

Brands by name

Popular brands

Hunter IMMS-CI-HW, Installation Instructions Manual

Search results

Summary of Contents for IMMS-CI-HW

Reviews:

Brands by name

Popular brands