Hunter IMMS-CI-HW Installation Instructions Manual Download Page 11

Page: 11 / 16

If the wrong address is set, reset the interface memory by

disconnecting the green three-wire power terminal. Press and hold

the green button, and plug the power terminal back in. Continue

holding the button until the test display “88” disappears, and release.

The display will show the version number for a moment, then the

“—“ display. Repeat the Controller Interface Address procedure to

enter the correct address.

INTERFACE RESET..................................................................................................................

Turn off or disconnect AC power plug before making any connections

inside the CI!

ADDITIONAL CONNECTIONS ................................................................................................

1. To connect to additional Controller Interfaces, route, strip, and

connect GCBL cable to the lower section of the CI communications

terminals in the same way that the incoming connection was made.

2. Connect the bare silver ground wire in the GCBL to the ground lug.
3. Continue the GCBL run to the next interface (IMMS-CI) in one

continuous run, if possible, with no breaks or splices in the

communications, and continue the installation.

CONNECTIONS TO OTHER INTERFACES ............................................................................

Summary of Contents for IMMS-CI-HW
















