manualshive.com logo in svg

Hunter ARCHITECT 90061, Installation Manual

Share
Download
Hunter ARCHITECT 90061 Installation Manual Download Page 5

B11

D

5/8
1/2

5/8
1/2

B12

Slide the mounting rails into brackets.

Position the correct depth mark at the bottom edge of 

the joist based on the thickness of your sheetrock.

    

E

B13

1/8"     

Bit

B14

Mark position of screws by using holes as a template.

Drill a hole in the center of each outline.

Pull wires through the strain relief.

Connect wires as shown.

A

A

A

Green

Black

White

Bare Copper

Ground

B19

B

D

B18

Tighten screws.

B17

Attach the rails onto the screws.

Insert screws, leaving space between the screw 

head and the joist. Screws are not provided.

B15

B16

 

New Construction – suspended between joists

8

9

B20

2

F

F

1

•

B21

2

G

Install the wiring cover plate. Make sure all 

wiring connections are inside the box or under 

the wiring cover plate.

 Tighten the wiring cover plate screw.

B22

Connect 4” duct and vent to the outside. Tape joints. 

If ducting does not fit securely, an adapter may need 

to be purchased.

 

41721-01  12/25/2004

 

41721-01  12/25/2004 

Summary of Contents for ARCHITECT 90061











Reviews:

No comments

Brands by name

Popular brands

Load more brands