For the most effective and safe use of Microban’s Warm Mist humidifier, please
ReAd And SAve tHeSe inStRUCtiOnS! especially those regarding adding salt.
• ALWAYS
place this warm mist humidifier on a firm, level, and water resistant surface. ALWAYS place the
warm mist humidifier at least six (6) inches away from walls and heat sources such as stoves, radiators,
or heaters.
• ALWAYS
place the warm mist humidifier in an area that is out of the reach of children especially infants
or toddlers. Supervision is necessary when the warm mist unit is used near children, patients, or pets.
Microban realizes that many customers use warm mists humidifiers in their homes with small children.
Please take the time to instruct children that the warm mist unit is not a toy. Warm mist humidifiers produce
steam that could cause serious burns.
• Before using the warm mist humidifier, extend the cord and inspect for any signs of damage.
dO nOt
use
the product if the cord has been damaged.
• This product has a polarized plug (one blade is wider than the other) as a safety feature. This plug will fit
into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician.
dO nOt
attempt to defeat or override this safety feature.
• ALWAYS UnPLUG
the warm mist unit when it is not in operation or while it is being emptied, filled, or
cleaned.
• The warm mist humidifier should always be placed at least four(4) feet from a bedside and out of reach of
the patient or children.
• Always ensure the warm mist humidifier is sitting flat on the surface it is placed and not resting on the cord
or other obstructions. Ensure the warm mist humidifier cord is tucked away as to prevent the warm mist
form being upset or turned over.
• dO nOt
add medication of any type into the water in the container. Do not cover the steam outlet or
place anything over it while the warm mist humidifier is operating. Never drop or insert any object into
any opening.
• Never fill the humidifier tank with hot water. Always use clean, cool tap water.
1. Remove the plastic bag covering from the humidifier.
2. Unravel and straighten the cord before use.
3. Remove the 1/16th teaspoon from the box and set aside.
4. Remove the steam unit from the tank. Hold the steam unit securely and
press the release button just above the power cord on the back of the steam
unit and pull straight up and off. Figure 1 and 2.
5. Fill the tank with clean, cool tap water until the water level is up to the MAX
mark in the Water Level Window.
dO nOt OveRFiLL
.
CAUtiOn: dO nOt
use the humidifier with extension cords.
Caution:
Never fill the humidifier with hot water.
6. Replace the steam unit in the tank and push down until the tabs fit in the
tank and lock into place.
nOte:
Protect your floor and furniture by placing the humidifier on a non-
metallic, waterproof, heat-resistant surface.
7. When using humidifier medications, fill the medicine cup on the steam
unit as directed by the medicine package.
nOte: dO nOt
add medication of any type into the water in the tank.
8. Plug the power cord into 110-120 Volts AC outlet protected up to 15
Amps. The humidifier will produce a gentle flow of steam within a few
minutes.
9. If steaming does not start within ten minutes, unplug the steam unit and
allow to cool.
10. Remove the tank from the steam unit and add 1 spoonful of ordinary table salt, using the 1/16th
teaspoon included with your humidifier, to the water and mix thoroughly.
Caution:
Do not mound salt in the spoon. Salt should be level with the top of the spoon.
See Figure 3.
11. Reassemble the unit and run normally. If the unit still does not steam, unplug the unit
and let it cool. Add 1 more leveled spoonful of salt and mix thoroughly.
Warning: DO NOT add more than 2 leveled spoonfuls to the water.
The humidifier will automatically stop producing steam when the water has reached the
minimum level. The power light will remain on indicating that the humidifier is still plugged
in. ALWAYS unplug the steam unit and allow to cool before removing the tank.
At A Glance
Warnings
1
Using Your Humidifier
Initial Setup and Operation
2
Maintenance
Cleaning and Storage
4
note: ALWAYS
unplug the steam unit from the electrical outlet and allow the unit to cool before cleaning.
Never remove the Steam Unit while it is plugged in, electrocution or burning could occur.
dO nOt
attempt to
disassemble the steam unit. NEVER allow water to sit in the tank when not in use.
daily Maintenance:
1. Unplug the steam unit and allow it to cool.
2. Remove the steam unit by pressing the release button on the back above the power cord and pulling it
straight off the tank.
3. Let all water drain back into the tank from the steam unit.
4. Turn the tank upside down and drain any water into a sink or tub. Shake the unit gently to remove any
remaining water.
5. Rinse the tank thoroughly with water, empty, and wipe with a dry, clean cloth.
6. Wipe the steam unit shaft with a dry cloth.
7. If the medicine cup was used, wipe it out with a slightly damp clean cloth.
8. Refill the tank as directed under “initial setup and operation” and resume use.
44075-01 • 10/25/2010
©2010 Microban
Figure 2.
Tabs
Figure 1.
Release
Button
Using Your Humidifier
Controls
3
Speed Control:
OFF
Steam off
Low: Extends the time between refills.
High: Average refill rate and optimal for day use.
™
nitelight:
Turns on or off the humidifier’s nitelight.
Humidity Adjustment Knob:
Adjusts the humidty levels between 30% and 80% humidity output.
Refill tank Light:
Comes on when the water in tank has reached minimum level. The light will turn
off as soon as the tank has been refilled.
Power Light:
Indicates the unit is on and should be running. If it is not, check the water level, or humidity setting.
end of Season Maintenance:
1. Follow the instructions for weekly maintenance before storing the unit.
2. Ensure all parts are completely dry before storing the unit.
3. Store the unit in a cool dry place.
4. Never store the unit with water in the tank.
Weekly Maintenance:
1. Unplug the steam unit and allow it to cool.
2. Remove the steam unit by pressing the release button on the back above the power cord and pulling it
straight off the tank.
3. Let all water drain back into the tank.
4. Turn the tank upside down and empty any water into a sink or tub.
5. Create a 50/50 solution of vinegar and water which should be 1/2 gallon vinegar and 1/2 gallon water.
Pour this solution into the tank. Be sure to only fill the tank to the MAX line as indicated on the water level
window on the front of the tank.
6. With the steam unit unplugged, place it back into the tank and soak for 30 minutes. After soaking for 30
minutes, remove the steam unit.
7. Empty the solution from the tank and rinse the tank. Fill the tank with tap water to the MAX line as indicated
on the water level window on the front of the tank. Place the steam unit back into the tank for 30 seconds.
Remove the steam unit and empty the water. Repeat the rinsing steps until the vinegar smell is gone.
8. Dry with a clean cloth. Clean the medicine cup with a slightly damp clean cloth.
note:
The tank has built-in antimicrobial properties to inhibit the growth of bacteria, mold, and fungi that
may affect the water in the tank. Daily and weekly maintenance are still necessary to prevent the growth of
bacteria, mold, and fungi.
Figure 3.
Figure 4.
