background image

14

45007-01  •  06/11/09  •  Hunter Fan Company

In warm weather

, use 

downward air flow pattern

In cold weather

, use upward 

 

air flow pattern

10-1.   Turn on electrical power to the fan.
10-2.   Ceiling fans work best by blowing air downward 

(counterclockwise blade rotation) in warm weather to cool the 
room with a direct breeze. In winter, having the fan draw air 
upward (clockwise blade rotation) will distribute the warmer air 
trapped at the ceiling around the room without causing a draft. 

10-3.   For cleaning finishes, use a soft brush or lint-free cloth to 

prevent scratching. A vacuum cleaner brush nozzle can remove 
heavier dust. Remove surface smudges or accumulated dirt and 
dust using a mild detergent and a slightly dampened cloth. You 
may use an artistic agent, but never abrasive cleaning agents as 
they will damage the finish.

10-4.   Clean wood finish blades with a furniture polishing cloth. 

Occasionally, apply a light coat of furniture polish for added 
protection and beauty. Clean painted and high-gloss blades in 
the same manner as the fan finish.

To Change Airflow Direction

Turn the fan off and let it come to a complete 
stop. Slide the reversing switch on the fan to the 
opposite position. Restart fan.

Reversing 
Switch

10 • Operating and Cleaning Your Ceiling Fan

Summary of Contents for 20174
















Reviews: