Hunter Stoves Telford Inset 20DB CVWSTI08DBFM Instructions For Installation/Operating/Maintenance/Servicing Download Page 4

JINTDBW09 Rev B 05/03/15 

 
 
 

 
 
 
 
 
 
 
 
G

ENERAL 

G

UIDANCE

 

It  is  important  that  your  stove  is  correctly 
installed  and  operated  as  Hunter  Stoves  cannot 
accept responsibility for any fault arising through 
incorrect  installation,  use,  maintenance  or 
servicing. 
 
These  instructions  cover  the  basic  principles  to 
ensure  satisfactory  installation  of  the  stove, 
although  detail  may  need  slight  modification  to 
suit particular local site conditions.  
 
The installation must comply with current Building 
Regulations,  National  and  European  Standards, 
Local  Authority  Byelaws  and  other  specifications 
or regulations as they affect the installation of the 
appliance.  
 
The  Building  Regulations  requirements  may  also 
be 

met 

by 

adopting 

the 

relevant 

recommendations  in  the  current  issues  of  British 
Standards BS 8303 and BS EN 15287-1. 
 
Only  use  approved  fuels  on  this  appliance. 
Information about this can be found on Page 18. 
 
This  is  a  Domestic  Appliance  and  must  only  be 
used in accordance with these instructions. 
Do  not  place  articles  that  are  affected  by  high 
temperatures  on,  or  near,  this  appliance.  Do  not 
place  furniture  or  other  items  within  700mm  of 
the  front  of  this  appliance.  See  the  note  on 
material clearances on page 10. 
 

Extractor Fans and/or Cooker Hoods must not be 
installed  in  the  same  space  or  room  as  this  can 
cause the appliance to emit fumes into the room. 
 
Do  not  obstruct  the  ventilation  required  for  the 
safe use of this appliance. 
 

C

OMPETENT 

P

ERSONS 

S

CHEME

 

Hunter  Stoves  recommend  that  this  stove  is 
installed  by  a  member  of  an  accredited 
competent persons scheme e.g. HETAS. 
 
If  the  installer  is  not  a  member  of  a  competent 
person’s scheme, it is  a legal requirement, in the 
UK, to notify your Local Building Control Officer in 
advance of any installation work starting. 
 

H

EALTH AND 

S

AFETY 

P

RECAUTIONS

 

Special  care  must  be  taken  when  installing  the 
stove  such  that  the  requirements  of  the  Health 
and Safety at Work Act are met. 
 

H

ANDLING

 

This  appliance  is  very  heavy.  Adequate  facilities 
must  be  available  for  loading,  unloading  and  site 
handling 
 

F

IRE 

C

EMENT

 

Some types of fire cement are caustic and should 
not be allowed to come into contact with the skin. 
In case of contact, wash immediately with plenty 
of water.  

 
 

 

IMPORTANT INFORMATION 

PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION AND OPERATION. 

 

KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE AND SERVICING. 

 

THIS APPLIANCE WILL BECOME HOT WHEN USED IN ACCORDANCE WITH THESE INSTRUCTIONS. 

HUNTER STOVES RECOMMEND THAT AN APPROVED GUARD IS USED TO PROTECT THE YOUNG, 

ELDERLY OR INFIRM FROM HARM. 

 

THE INSTALLER COMMISSIONING SHEET CAN BE FOUND ON THE BACK COVER. 

PLEASE ENSURE THAT IT IS COMPLETED PRIOR TO USE. 

Summary of Contents for Telford Inset 20DB CVWSTI08DBFM


























Reviews: