background image

 

 
The digital depth readout will continue to track the bottom even when Zoom is enabled. 
Bottom Lock is a function of zoom, except the depth adjustment is controlled automatically to view the 
area immediately above the bottom. This is especially useful if you are looking for structure or minor 
variations in terrain in areas of relatively flat bottom terrain. To enable Bottom Lock, press ENTER until 
the "BL" is highlighted. The zoom range will be controlled by the current depth range, as in Zoom, and will 
be indicated on the Zoom menu. 
 
 

Bottom Alarm 

 
The Wide Vision contains an audible alarm to warn you of shallow water depths. This alarm is adjustable 
from 2' to 99' of depth. To enable the alarm, simply adjust the alarm depth using the UP and DOWN arrow 
buttons, and press ENTER. Whenever the depth of the water beneath your boat is equal to or less than 
the selected alarm depth, a continuous alarm will sound.  
 

 

 
To disable the alarm, either move to deeper water, or select the Bottom Alarm menu, and press ENTER 
to turn the alarm off. 
 

 
Fish Alarm 

 
The Fish Alarm alerts you to the presence of fish, or other targets not attached to the bottom, in the water 
beneath your boat. The Fish Alarm has 3 different settings which correspond to the 3 different size fish 
targets shown on-screen. 
 

Summary of Contents for Wide Vision

































Reviews: