background image

4. Enabling Bottom Alarm; 
Factory Setting: OFF 
 
 
 
 

The Bottom Alarm lets you specify the minimum 

depth you want to maintain. To use it, select BOTTOM 
ALARM; then press the ON-OFF button to activate the 
alarm, and the UP or DOWN arrow button to adjust the 
depth at which the alarm will sound. A dashed line 
appears at the alarm depth when this function is on. 
 
 

When Bottom Alarm is on, you'll hear a 

continuous chirping sound when the bottom is shallower 
than you defined. This is very handy for alerting you to 
shallow water or helping you to maintain position over 
structure. 
 
 
 
 
 
 
 
 
 
 
 
 
5. Enabling Fish Alarm; 
Factory Setting: OFF 
 
 
 
 

The Fish Alarm alerts you with a chirping sound 

whenever the Platinum ID detects fish (or another object 
not attached to the bottom). To activate it, select FISH 
ALARM and press the ON-OFF button. 
 
 

Initially, the fish alarm will sound when any target 

not attached to the bottom is detected. The word "ALL" is 
displayed on the menu and two fish are shown on the lower 
part of the display. By pressing either arrow button, the 
word "LARGE" appears on the display and the alarm will 
only sound when a large target is detected. A single fish 
symbol is shown on the bottom of the display to represent 
that large fish only is selected. While there is some 
variation in sonar characteristics of different species, 
typically, the strength of the return is relative to the size of 
the fish. 
 
 
 
 
 
 

Summary of Contents for Platinum ID 600



















Reviews: