Hughes DIRECWAY DW7000 User Manual Download Page 27

Page: 27 / 98

Chapter 2 • System Control Center

1035978-0001 Revision A

System Status page

The System Status page is shown in Figure 8.

•

Signal Strength -

displays the receive signal strength. A value

of 30 or less indicates an appropriate signal is not being
received. Refer to Weather and signal strength on page 24 for
more information on factors that might affect signal strength.

•

Transmit Status -

indicates whether the transmit data path is

operational. Clicking on the status message displays
corresponding help information.

•

Receive Status -

indicates if the receive data path is

operational. Clicking on the status message displays
corresponding help information.

•

Software Download Status -

indicates whether DW7000

software and configuration is current.

•

Commission Status -

indicates whether or not the DW7000 is

commissioned.

•

TCP Acceleration Status -

indicates whether or not TCP

Acceleration is operational. TCP acceleration must be
operational for optimal performance on a DW7000.

Figure 8: System Status page

Summary of Contents for DIRECWAY DW7000



































































































Search results

Summary of Contents for DIRECWAY DW7000

Reviews:

Hughes DIRECWAY DW7000, User Manual, Page: 27 / 98

Search results

Summary of Contents for DIRECWAY DW7000

Reviews: