manualshive.com logo in svg

Hughes DIRECWAY DW7000, User Manual, Page: 38 / 98

Share
Download
Hughes DIRECWAY DW7000 User Manual Download Page 38

Chapter 3 • Remote terminal LEDs

 

24

1035978-0001  Revision A

Fatal error indication

If the Power LED is off and one or more of the other LEDs is 
flashing, the unit may have to be replaced. Try power cycling the 
terminal by unplugging the power cord from the power source 
and then plugging it back in. The terminal may recover. If the 
fatal error indication continues, the terminal must be replaced. 
Contact customer support.

Weather and signal 
strength

Rain or snow can interfere with signal strength. The terminal 
stops receiving satellite signals, and the Receive LED turns off.

Heavy rain or snow can interfere with the antenna’s reception of 
the signal. In addition, buildup of moisture, snow, or ice on the 
antenna can interfere with the signal. Similar conditions at the 
NOC can interfere with signals for brief periods of time.

Severe weather conditions may interfere with signal reception. 
Signal strength is restored as the rain or snow subsides.

LED appearance during 
normal operation

This section describes the LEDs’ appearance during typical 
terminal operation. Refer to Figure 16 for LED locations.

Figure 16:  Remote terminal LEDs

Summary of Contents for DIRECWAY DW7000



































































































Reviews:

No comments