Installation Manual 3000B
Page 4 of 9
May 2012
Make sure rings are seated properly in groove and the mark
drawn on ring lines up with the mark on the socket. Gaps be-
tween upper and lower retainer halves should be equal. Install
lock screw into each retainer ring half. Hold ring in place with
screwdriver while tightening screws. Hand tighten the blade
socket cap screws.
DO NOT TIGHTEN JAM NUTS.
INSTALL SEVERE DUTY RETAINING
RING (OPTIONAL EQUIPMENT)
If included, place severe duty retainer (SDR as shown in Figure
5A; for old recessed-ear hubs, both the old 65289 SDR and the
D3246 retro-fit spacer are required) into the blade socket cavity
by either pushing it directly into position on top of socket or by
pushing it into the blade socket at 90° to one side and then rotat-
ing it into position on top (12:00) side. Refer to the following
Figures 5A, 5B or 5C.
Figure 5A
Figure 5B (new style hub & SDR)
Figure 5C (old style hub & retro-fit SDR)
NEW,LONGER
SCREW,CAP,
HH,3/8-16x2-1/4,
F593,316,SS,
FULL THREAD,
P/N 69934
WASHER,LOCK,3/8"
316,SS,P/N 73722
NEW STYLE,RETAINER,
BLADE,SEVERE DUTY
P/N D3261, DWG 3261
FLUSH-EAR HUB BODY, 3000B &
1000B, NEW STYLE
T-L I BLADE
SCREW,SELF-TPG,PH,#8-32x5/8,
410,THREAD CUTTER TYPE F,
SLOTTED. P/N 72661
SCREW,CAP,HH,
3/8-16x1-3/8,
F593,CHAMFER,
316,SS.
P/N 72338
NUT,JAM,3/8"-16,
F594,316 SS.
P/N 72051
RING,BLADE
RETAINER,AV-268,
HALF,MONEL,
DWG 268,P/N 62380
3
2
1
REF: HUDSON PARTS
KIT K2202 FOR
(1) SDR ASSEMBLY
Figure 10B (new style hub & SDR)
Figure 10C (old style hub & retro-fit SDR)
NEW,LONGER
SCREW,CAP,
HH,3/8-16x2-1/4,
F593,316,SS,
FULL THREAD,
P/N 69934
WASHER,LOCK,3/8"
316,SS,P/N 73722
NEW STYLE,RETAINER,
BLADE,SEVERE DUTY
P/N D3261, DWG 3261
FLUSH-EAR HUB BODY, 3000B &
1000B, NEW STYLE
T-L I BLADE
SCREW,SELF-TPG,PH,#8-32x5/8,
410,THREAD CUTTER TYPE F,
SLOTTED. P/N 72661
SCREW,CAP,HH,
3/8-16x1-3/8,
F593,CHAMFER,
316,SS.
P/N 72338
NUT,JAM,3/8"-16,
F594,316 SS.
P/N 72051
RING,BLADE
RETAINER,AV-268,
HALF,MONEL,
DWG 268,P/N 62380
3
2
1
REF: HUDSON PARTS
KIT K2202 FOR
(1) SDR ASSEMBLY
SCREW,CAP,HH,
3/8-16x2,F593,316,SS,
FULL THREAD,
P/N 53622
WASHER,LOCK,3/8"
316,SS,P/N 73722
RETAINER,BLADE,SEVERE
DUTY,P/N 65289, DWG 3781
SPACER,BLADE RETAINER,3000B
P/N B3246, DWG 3246
RECESSED-EAR HUB BODY,
3000B, OLD STYLE
T-L I BLADE
SCREW,SELF-TPG,PH,#8-32x5/8,
410,THREAD CUTTER TYPE F,
SLOTTED. P/N 72661
SCREW,CAP,HH,
3/8-16x1-3/8,
F593,CHAMFER,
316,SS.
P/N 72338
NUT,JAM,3/8"-16,
F594,316 SS.
P/N 72051
2
1
3
REF: HUDSON PARTS
KIT K2200 FOR
(1) SDR ASSEMBLY
It may be necessary to partially loosen the four (4) blade socket
cap screws (labels 1 & 2 in Figure 5B and/or jostle the blade
slightly to initially place the SDR part into its assigned position
as shown in Figure 5B or 5C.
Now insert the two (2) 3/8” cap screws (labeled 3 in Figure 5B
or 5C) and lock washers into the SDR and finger tighten only.
Note A:
The four (4) blade socket cap screws and the two (2) SDR cap
screws are maintained finger-tight until the blade(s) is (are) adjusted for
both blade pitch and blade track. After a gradual trial & error series of
adjustments, occurring in subsequent portions of this manual, these same
cap screws shall at completion achieve final tightness to specified torque
values.
