PD2462
(Page 2)
09/12
PRINTED IN U.S.A.
I
NSTALLATION INSTRUCTIONS
–
furniture feed only
Follow installation instructions from Concrete fl oor
installation.
1. Type S1R6FFxx factory assembled furniture feeds are shipped
with closure plugs (m) and (n) for the ¾” and 2” openings.
Openings must always be plugged when not in use. If
installation requires closure plugs apply Tefl on® tape or sealant
onto threads and tighten into threaded hole. Type S1R6FFxx
factory assembled furniture feeds is supplied with (2) metallic
screw-in connector fi ttings, (p) and (r). If installation requires
connector fi ttings apply Tefl on® tape or sealant onto threads
and tighten into threaded hole.
2. A maximum of (10) #10 AWG type THHN (T-90 NYLON in
Canada) conductors may be fed through the ¾” opening side
of the service fi tting.
3. A maximum of (30) Category 6 data cables (#23 AWG, 8
conductors, 4 twisted pair cable) may be fed through the 2”
opening side. When conductors larger than #22 AWG are
used, the aggregate cross sectional area must not exceed
the maximum of (30) Category 6 data cables (#23 AWG, 8
conductors, 4 twisted pair cable).
4. Remove the installation plate (j) and black spacer (o) and
retain the screws.
5. Feed wires through ¾” opening side and through tube (s).
6. Insert intumescent material sheet into interior of the can
assembly and around the tube (s).
7. Use the provided fl oor gasket (v) or apply a ¼ [6.3mm] thick
continuous bead of electrical type of RTV silicon sealant
compound fully around the perimeter on the underside of the
fl ange (w).
8. Attach Furniture Feed Cover fl ange (w) to the service fi tting
(x). Align the tube (s) with smaller hole in bottom of the can.
Fasten cover (y) to feed cover fl ange (w) with three oval
screws (z) provided.
9. Attach ¾” and/or 2” liquid tight nonmetallic conduit (af) as
required to metallic screw in connectors. Nonmetallic conduit
is required to maintain the fi re rating of the poke through
installation.
ABANDONMENT PLATE INSTALLATION INSTRUCTIONS
(Purchased separately)
:
S1R6ADMTxx abandonment plates provide an approved
method of abandoning the Hubbell S1P6PTxx series fi re rated
poke through. This product will maintain the fi re rating of the
poke through installation.
1. Disconnect power and/or telephone/data of the poke through.
2. Remove cover assembly by removing screws (ax) attaching
cover to the can. See Figure 11.
3. Install black spacer (o) and abandonment plate item (ag).
Coat supplied screws with sealant compound to ensure water
tightness before installing. Coat cover perimeter to ensure
water tightness.
PRE-POUR TUBE (PPT) INSTRUCTIONS (Purchased
separately):
Slide (3) tube segments (aa) together using dovetail joints.
Segments are identical except for location of holes (ab).
Assemble brackets (ad) as required as shown in fi gures 4 and 5.
Brackets are marked to assist assembly. Turn hexagonal head
screws (ae) horizontally to support the disc (at). Insert discs (at)
at top, center and bottom. Bend brackets (af) for center and
bottom positions to fi t inside the assembled tube segments.
STEEL DECK INSTALLATION
1. Cut hole 6.06” to 6.12” in diameter into deck.
2. Install assembly into cut hole, see Fig.4. Check that the
assembly is installed plumb to the deck. Attach to deck with
sheet metal screws (not supplied).
3. Adjust the height of the assembly so that the top of the cap
protrudes above the maximum thickness of the desired
concrete pour.
4. Seal perimeter of PPT with tape.
PLYWOOD DECK INSTALLATION
1. Attach assembly to the deck with appropriate fasteners (not
provided). See Fig. 5.
2. Seal deck area around PPT with tape.
AFTER ASSEMBLY – Pour concrete and let cure. AFTER
CURE - Remove discs (at) and hexagonal head screws (ae).
rive one of the segments (aa) downward until released from the
concrete. Brackets (ad) will remain inside the resulting hole.
Fig. 10
Fig. 11
Fig. 3
Fig. 4
Fig. 5
(ab)
(ad)
(ae)
(af)
(aa)
(at)
(at)
