background image

Pub. 42004-541A 

 Hands-free VoIP Telephone Manual 

Page 7 of 24 

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-541A.docx 

02/20 

 

warm reset (internal command) 

 

keypad error (if applicable) 

 

key hook (off hook status, if applicable) 

 

register fail (unsuccessful SIP registration) 

 

audio path test (speaker/microphone test) 

Status Indication

 

Power 

The 

ON

 LED, located on the VoIP PCBA (see Figure 21 on Page 18), illuminates when power is applied 

to the telephone. 

Heartbeat 

The 

HB

 LED, located on the VoIP PCBA (see Figure 21 on Page 18), flashes when communication over 

the LAN is established. 

Link 

The 

L

NK 

LED, located on the VoIP PCBA (see Figure 21 on Page 18), indicates an active network 

connection when illuminated. 

Speed 

The 

SP

 LED, located on the VoIP PCBA, (see Figure 21 on Page 18) indicates a 100 Mbps network 

connection when illuminated or a10 Mbps connection when off. 

VoIP Circuit PCBA Pushbuttons

 

Reset 

Press the 

RESET

 button (see Figure 21 on Page 18) momentarily to warm reboot the telephone.  The 

telephone maintains the current configuration. 

Factory 

Use the 

FACTORY

 button (see Figure 21 on Page 18) to erase the current configuration and restore the 

factory default settings as follows: 

1.

 

Press and release the 

RESET

 button. 

2.

 

Press and hold the FACTORY button for 10 seconds while the telephone is rebooting. 

The telephone will reboot again with the factory default settings configured. 

Summary of Contents for GAI-TRONICS RED ALERT 393-710




























Reviews:

Related manuals for GAI-TRONICS RED ALERT 393-710