background image

Pub. 42004-541A 

 Hands-free VoIP Telephone Manual 

Page 6 of 24 

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-541A.docx 

02/20 

 

the defined call-duration timeout is exceeded 

 

the SIP server disconnects the call 

General Telephone Calls

 

Models 394AL-712, 398-711, 398-711FS, and 398-712

 

To place a general telephone call: 

1.

 

Press the 

CALL

 push button. 

2.

 

Wait for the dial tone. 

3.

 

Use the keypad to dial the desired number. 

 

The 

CALL

 

RECEIVED

 

WHEN

 

LIT

 LED illuminates steadily in accordance with the ADA when 

the call is answered. 

 

The call is terminated by any of the following: 

 

pressing the 

CALL

 push button again 

 

the receiving caller hangs up 

 

the defined call-duration timeout is exceeded 

 

the SIP server disconnects the call. 

Receive a Call

 

RED ALERT VoIP emergency telephones automatically go off-hook (auto-answer) when called.  A 
conversation can then take place. 

Multicast Broadcast

 

When making a multicast call, the SIP server sends the page request to a specific IP address and multiple 
telephones accept and play the subsequent audio.  GAI-Tronics’ VoIP telephones can be programmed for 
up to eight multicast addresses to permit the receipt of multicast broadcasts from different sources or to 
enable zoning of broadcasts.  Each multicast address can be assigned a priority (via programming) to 
define broadcast override.  A telephone with multicast enabled can still make and receive normal calls 
(peer-to-peer or SIP server).  Normal calls can be assigned a priority level, defining whether calls can 
override multicasts or vice versa. 

Monitoring and Reporting

 

Each telephone can recognize and generate several hardware and configuration fault condition alarms.  
These alarms can be signaled to a remote site using three methods: 

 

Syslog output over TCP 

 

SNMP (Simple Network Management Protocol) 

 

TMA (Telephone Management Application) software (purchased separately) 

N

OTE

:

  The TMA software permits 

system

 monitoring and data collection/reporting from a central 

location. 

Available alarms are: 

 

handset integrity loop (if applicable) 

 

configuration error 

 

cold reset (power cycle) 

Summary of Contents for GAI-TRONICS RED ALERT 393-710




























Reviews:

Related manuals for GAI-TRONICS RED ALERT 393-710