FOR REFERENCE ONLY
MOUNTING FEET SHOWN AS INSTALLED
SECTION A-A
SECTION B-B
A
A
B
B
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A
A
B
B
C
C
D
D
STANDARD ENCLOSURE
DESCRIPTION
ALL DIMENSIONS ARE IN INCHES
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE
CUSTOMER
DATE
DWG
AH12106
± 0.03
± 0.010
SCALE
10/26/16
AJC
DRAWN BY
AH12106
1, 3R, 4, 4X, 12
COLOR:
NEMA 250: TYPE
UNLESS SPECIFIED
TOLERANCES
PART NUMBER
.XX
.XXX
ATAH12106
SPECIAL REQUIREMENTS
MATERIAL: POLYCARBONATE
THIS DRAWING IS THE SOLE AND EXCLUSIVE
PROPERTY OF ROBROY ENCLOSURES.
NO PART OF THIS DRAWING MAY BE
REPRODUCED, DISTRIBUTED, OR PUBLICALLY
DISPLAYED IN ANY FORM OR BY ANY MEANS
WITHOUT THE EXPRESS WRITTEN
PERMISSION OF ROBROY ENCLOSURES.
ALL RIGHTS RESERVED
UNDER THE COPYRIGHT LAWS.
COPYRIGHT © ROBROY ENCLOSURES
STANDARD P/N:
CUSTOMER DWG:
COLOR STANDARD:
IEC 60529:
IP66
N/A
PANTONE 7541 C
2016
Robroy Enclosures
500 Maple Street
Belding, Michigan 48809
Phone: 616-794-0700
Fax: 616-749-3378
ASSEMBLY:
1. (1) ACCESSORY KIT (WPPCACCKIT) SHALL BE PACKAGED LOOSELY INSIDE ENCLOSURE
HARDWARE INCLUDED:
-(4) #1/4-20 x 1/2 FLAT HEAD PHILLIPS MACHINE SCREW (RMSC1/4-20X.5FLPH)
-(4) #10-32 x 5/8 PAN HEAD PHILLIPS MACHINE SCREW (RMSC10/32X5/8SS)
-(4) #10-32 x 3/8 PAN HEAD SCREW (RMSC10/32X3/8ZN)
-(4) #10 WASHER (RMWAS10ZN)
2. (1) STYROFOAM SHEET SHALL BE PLACED ON TOP OF COVER INSIDE CARTON
REVISION HISTORY
REV
DESCRIPTION
DATE
ENG
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
11.41
13.41
10.81
7.87
12.00
11.95
12.81
10.25
10.00
9.95
9.63
7.63
1.18
12.68
0.44
7.05
14.03
8.24
0.14 TYP
0.187 TYP
7.38
14.88
3905C 100621
1
NX Energy Dashboard
INSTALLATION GUIDE
Description
The Hubbell Control Solutions’ NX energyHUBB™ hosts the energy dashboard. The energyHUBB system is housed in an
enclosure where its pre-wired and assembled on a DIN rail and connected to a DIN rail power supply. (See Figure 1)
The energyHUBB system contains a system processor, web server-based user interface, data storage and network
interface components required for system operation.
The energyHUBB module connects with the NX network through the Area Controller using a standard Ethernet cable.
A standard Ethernet connection is provided on the module itself which can be used to connect directly to the area
controller customer Ethernet port. Additionally, the energyHUBB module can also be connected to the building LAN
router. (See Figure 2)
The NEMA1 grade enclosure has a hinged locking door and is suitable for surface wall mounting in a conditioned
electrical room.
Precautions
Read and understand all instructions before beginning installation.
NOTICE
: For installation by a licensed electrician in accordance with National and/or local Electrical Codes and the
following instructions.
•
Disconnect switch or a circuit breaker must be provided and marked as the disconnecting device.
•
Disconnect switch/circuit breaker must be within reach of operator.
CAUTION
:
RISK OF ELECTRICAL SHOCK.
Turn power off at service panel before beginning installation. Never wire
energized electrical components.
CAUTION
:
USE COPPER CONDUCTOR ONLY
Confirm device ratings are suitable for application prior to installation. Use of device in applications beyond its
specified ratings or in applications other than its intended use may cause an unsafe condition and will void
manufacturer’s warranty.
NOTICE
: Do not install if product appears to be damaged.
SAVE THESE INSTRUCTIONS!
Figure 1.
701 Millennium Blvd. | Greenville, SC 29607 | (864) 678-1000 | hubbellcontrolsolutions.com
Copyright © 2021 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identifiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
affiliation with or endorsement by such respective owners.
