Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 56 / 138

Tools and Instruments

Torque

screwdriver

Cable cutter

Brush

Flat-head

screwdriver
(2–5 mm)

Phillips

screwdriver
(M3/M4/M5/M6/

M8)

Insulated torque

wrench
(M6/M8/M12/

M16)

Heat shrink

tubing

Insulated

adjustable wrench

NO TE

Table 3-1

lists only the common tools for installation and cable connection. For more dedicated

tools required, see the corresponding component manuals. Prepare tools based on site

requirements.

3.1.3 Preparing Power Cables

NO TICE

● The UPS can generate large leakage currents. A circuit breaker that provides

leakage current protection is not recommended.

● If multiple UPSs are to be connected in parallel, input and output power cables

for each UPS should have the same length and specifications.

Table 3-2

lists the recommended cross-sectional areas for UPS power cables. Note

that the currents listed are measured at a rated voltage of 380 V (line voltage).

Table 3-2 Recommended cross-sectional areas for power cables

Item

Specifications

30 kVA

60 kVA

90 kVA

120 kVA

Mains

input

Mains input current (A)

110

165

220

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

3 Installation

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands