Huawei U8650 Maintenance Manual Download Page 58 | Manualshive

Page: 58 / 101

background image

U8950 Maintenance Guide V1.0

10 Principles and Failure Analysis

2012-10-22

Huawei Proprietary and Confidential

54

The dedicated power chip FAN5402UCX is used to charge the U8095 with a current of 1 A.
I2C is used for communication and control with two interfaces GPIO13 (I2C_SCL_DCDC)
and GPIO98 (I2C_SDA_DCDC) respectively. This charging management chip (BQ24152)
sources the power from VCHAG in the USB interface and is controlled by I2C. The BQ24152
chip outputs VPH_PWR to supply power to the PM and battery.

Figure 10-1 shows the functional blocks of the BQ24152 chip.

Figure 10-1

Charging chip's functional block diagram

Figure 10-2 shows the charging flowchart.

«
...
56
57
58
59
60
...
»

Summary of Contents for U8650






































































































Reviews:

No comments

Related manuals for U8650

T-Mobile KX-HDV130

Brand: Panasonic Pages: 104

Brand: Panasonic Pages: 13

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 36

Brand: Kalley Pages: 32

Brand: Airbus Pages: 123

Brand: EMPORIA Pages: 40

8700 - 8707H SMARTPHONE

Brand: Blackberry Pages: 48

Brand: Amron Pages: 28

Brand: Dash Pages: 24

Brand: Blu Pages: 21

Brand: Grandstream Networks Pages: 50

Brand: Sonim Pages: 89

Brand: snopfon Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands