Huawei SUN2000-60KTL-M0 User Manual Download

Page: 21 / 127

2.3.2 Product Nameplate

Figure 2-4 Nameplate of the SUN2000-60KTL-M0

(1) Trademark, product name, and model

number

(2) Important technical specifications

(3) Compliance symbols

(4) Company name and place of production

NO TE

The nameplate figure is for reference only.

2.4 Working Principles

2.4.1 Conceptual Diagram

The SUN2000 receives inputs from 12 PV strings. Then the inputs are grouped into

six MPPT routes inside the SUN2000 to track the maximum power point of the PV

strings. The DC power is then converted into three-phase AC power through an

inverter circuit. Surge protection is supported on both the DC and AC sides.

Figure 2-5

shows the conceptual diagram for the SUN2000-60KTL-M0.

Figure 2-6

shows the conceptual diagram for the SUN2000-65KTL-M0.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

2 Overview

Issue 06 (2020-10-12)

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands