PIN code
■
PIN code
●
To prevent unauthorized use of the au IC card by a third party, you can set the product to require PIN code entry every time
the power is turned on. You need to enter the PIN code when setting whether to enter the PIN code or not.
●
If the PIN code is incorrectly entered three times consecutively, the PIN code will be locked. You can unlock the PIN code
using PUK code.
* By default setting, PIN code is “1234” and PIN code entry is not needed. However, you can change the PIN code to any
four- to eight-digit number and PIN code entry setting (entry is needed) as necessary. When an entry of security code is
required for making settings, change the initial value of the security code to your own number and then use it.
* PIN code is not reset by resetting the product.
■
PUK code
●
In case the PIN code is locked, you can unlock it by entering the PUK code.
* PUK code is an eight-digit number given at the time of purchase, and is printed on the back side of the plastic card on
which your au IC card is attached.
* After entering the PUK code, you need to set a new PIN code in “PIN management”.
* If the PUK code is incorrectly entered ten times consecutively, contact an au shop, PiPit or Customer Service Center.
Notes on data communication charge
• Since a constant Internet connection is possible with the product, data communication may be performed automatically.
• To configure various settings, connection to the Internet is required, to which data communication charge applies.
Mobile Device Etiquette
■
Use of the product is not allowed in the following places!
• Use of electric devices on board is restricted. Follow the instructions of each airline company.
■
Make sure where you are when using!
• Use the product in a place where it cannot block foot or traffic in a street.
• It is extremely dangerous to walk while looking at the screen of the product. Do not operate the product while walking or by
stopping suddenly.
• Move to a place where you do not disturb others while you are in shinkansen, a hotel lobby, etc.
• In a crowd such as crowded train, there may be people with a cardiac pacemaker nearby. Turn off the product beforehand.
• When a medical institution has laid down designated areas where use of the product is prohibited or is not allowed to be
brought in, abide by the instructions of that medical institution.
Operation environment of wireless LAN (Wi-Fi
®
)/USB connection
The operating environment for wireless LAN (Wi-Fi
®
)/USB connection with the product are as follows. (as of November of 2018)
■
Compatible devices
PC, iPhone, iPod touch, iPad, iPad mini, iPad Pro, smartphone, game console, etc. compatible with IEEE802.11a/b/g/n/ac
wireless LAN (Wi-Fi
®
) standard.
Windows PC/Mac with USB port
■
Compatible OS (PCs)
Windows 7 (32-bit/64-bit), Windows 8.1 (32-bit/64-bit), Windows 10 (32-bit/64-bit)
Mac OS X 10.9 (64-bit), Mac OS X 10.10 (64-bit), Mac OS X 10.11 (64-bit)
macOS Sierra 10.12 (64-bit), macOS High Sierra 10.13 (64-bit)
macOS Mojave 10.14 (64-bit)
For each OS, Japanese version/English version is supported.
* For Windows RT, USB connection is not supported.
■
Memory
Windows 7: 1 GB or more is required (32-bit), 2 GB or more is required (64-bit)
Windows 8.1: 2 GB or more is required
Windows10: 1 GB ore more is required (32-bit), 2 GB or more is required (64-bit)
Mac: 512 MB or more is recommended (256 MB or more is required)
■
Hard Disk
100 MB or more is recommended (50 MB or more free space is required)
Windows 8.1: 2 GB or more free space is required
Windows 10: 16 GB or more free space is required (32-bit), 20 GB or more free space is required (64-bit)
■
Screen resolution
1024 x 768 or more is recommended
■
USB port
USB 2.0, USB 3.0 or USB 3.1 (except USB ports by PC manufacturer
’
s specification)
* The transfer speed is for USB 3.0 standard when connecting to a PC supporting USB 3.1 via USB cable supporting USB 3.0.
■
Compatible browser (for Speed Wi-Fi NEXT setting tool)
Microsoft Internet Explorer 8.0 - 11.0
Microsoft Edge
Safari 10.0 - 12.0
Firefox 24.0 - 55
Chrome 41 - 69
Opera 41 - 55
iOS 8.0 - 12 standard browser
Android 4.1, 4.2, 4.3, 4.4, 5.0, 5.1, 6.0, 7.0, 7.1, 8.0, 8.1, 9.0 standard browser/Chrome
* Use outside these environments may affect performance. Also, even if an operating environment is applicable, the product
may not work properly depending on your using environment (PC, connected peripheral devices, applications, etc.).
Operation may not be performed properly depending on web browser settings such as proxy or security in Internet options.
* For PC support, OS version upgrade information, etc., see corresponding manufacturer’s manual and follow the instructions.
After-sales service
■
When asking for repair
For repair, contact Repair and Delivery Support Center
During the warranty period
Repairs will be done based on the terms of services of the free-of-charge repair warranty
described on the warranty card.
Outside the warranty period
We shall repair the product for a charge as requested by the customer if repair renders it usable.
* Warranty period is one year from the date you newly purchased the product.
• Before handing in the product for repair, make a backup of the contents of memory since they may disappear during repair.
Note that the Company shall not be liable for any damages and loss of income should the contents of memory be altered or lost.
• Recycled parts that meet the Company’s quality standards may be used for repair.
• Collected au products by Replacement mobile phone delivery service which you used before are recycled to products for
replacement after repairs. Also replaced parts by au after-sales service are collected and recycled by KDDI. They are not
returned to customers.
• Modified, remodeled, analyzed (including software alteration, analysis (including rooting), reverse engineering, decompiling,
or disassembling) products, or products repaired by repair offices other than the Company etc. specified are out of warranty
and repairs might be refused.
• The internal battery is not covered by the free-of charge repair warranty except for phenomenon arising from the material of
the battery or defect on production.
• USB Type-C to Micro B adapter (sample) is not covered by the free-of-charge repair warranty.
■
Performance parts for repair
The Company retains performance parts for repair of Speed Wi-Fi NEXT W06 main unit and its peripherals for four years after
discontinuation of production.
“Performance parts for repair” refers to parts required for maintaining the functions of the product.
■
Warranty card
At the store of purchase, thoroughly check and read the name of the retailer, date of purchase and other necessary details filled
in on the warranty card, and be sure to keep it in a safe place.
■
Repair and Delivery Support
An after-sales service membership program on a monthly basis called “Repair and Delivery Support” is available for using your
au product for a long time without worries. This service expands coverage for many troubles including malfunction, theft and
loss. For monthly fee or details of services, refer to au homepage.
https://www.au.com/mobile/service/kosho-funshitsu/
• You can apply for membership only at the time of purchasing your au product.
• Once you cancel the membership, you cannot reapply for it until you purchase an au product next time.
• Note that when changing the model or purchasing an extra au product, this service only covers the most recently purchased
au product.
• When an au product is handed over to you or someone else, the Repair and Delivery Support membership is also handed
over to the successor of the product.
• When you get a new au product by changing the model or purchasing an extra product, the Repair and Delivery Support
membership for the old au product is automatically canceled.
• Service contents are subject to change without notice.
■
au IC card
The au IC card is lent to you by au. In case of loss or damage, the card will be replaced at your expense. When malfunction is
suspected, or in case of theft or loss, contact an au shop or PiPit.
Specific Absorption Rate (SAR) of Mobile Terminals
This model Speed Wi-Fi NEXT W06 device complies with Japanese technical regulations and international guidelines regarding
exposure to radio waves.
This device was designed in observance of Japanese technical regulations regarding exposure to radio waves(*1) and limits to
exposure to radio waves recommended by a set of equivalent international guidelines. This set of international guidelines was
set out by the International Commission on Non-Ionizing Radiation Protection (ICNIRP), which is in collaboration with the World
Health Organization (WHO), and the permissible limits include a substantial safety margin designed to assure the safety of all
persons, regardless of age and health condition.
The Japanese technical regulations and international guidelines define the limits using a unit of measurement known as the Specific
Absorption Rate (SAR), which represents the average amount of radio frequency energy absorbed by the human body. The SAR
limit for mobile terminals is 2.0 W/kg. The highest SAR value for this device when tested for intended use described in the instruction
manual is 0.644 W/kg
(*2)
. There may be slight differences between the SAR levels for each product, but they all satisfy the limit.
The actual SAR of this device while operating can be well below that indicated above. This is due to automatic changes in the
power level of the device to ensure it only outputs the minimum power required to communicate with a base station. Therefore
in general, the closer you are to a base station, the lower the power output of the device.
During communication, hold the device farther than 1.5 cm away from your body without including any metals. By doing this, this data
communication terminal complies with Japanese technical regulations and international guidelines regarding exposure to radio waves.
The World Health Organization has stated that present scientific information does not indicate that use of mobile devices has
any harmful effects on the human body.
If you would like to know more detailed information, please refer to the WHO website.
http://www.who.int/emf
Please refer to the websites listed below if you would like more detailed information regarding SAR.
○
Ministry of Internal Affairs and Communications Website:
http://www.tele.soumu.go.jp/e/sys/ele/index.htm
○
Association of Radio Industries and Businesses Website:
http://www.arib-emf.org/01denpa/denpa02-02.html (Japanese)
○
HUAWEI TECHNOLOGIES CO., LTD. homepage:
https://consumer.huawei.com/jp/mobile-broadband/w06-au/ (Japanese)
○
au homepage:
*1 Technical regulations are defined by the Ministerial Ordinance Related to Radio Law (Article 14-2 of Radio Equipment Regulations).
*2 Including other radio systems that can be simultaneously used.
Disposal and recycling information
This symbol (with or without a solid bar) on the device, batteries (if included), and/or the packaging, indicates that
the device and its electrical accessories (for example, a headset, adapter, or cable) and batteries should not be
disposed of as household garbage. These items should not be disposed of as unsorted municipal waste and
should be taken to a certified collection point for recycling or proper disposal.
For more detailed information about device or battery recycling, contact your local city office, household waste
disposal service, or retail store.
Disposal of the device and batteries (if included) is subject to WEEE Directive Recast (Directive 2012/19/EU) and Battery
Directive (Directive 2006/66/EC). The purpose of separating WEEE and batteries from other waste is to minimize the potential
environmental impacts and human health risk of any hazardous substances that may be present.
Reduction of hazardous substances
This device and any electrical accessories are compliant with local applicable rules on the restriction of the use of certain hazardous
substances in electrical and electronic equipment, such as EU REACH, RoHS and Batteries (where included) regulations, etc. For
declarations of conformity about REACH and RoHS, please visit our web site https://consumer.huawei.com/certification.
EU regulatory conformance
■
RF exposure requirements
Important safety information regarding radio frequency (RF) radiation exposure:
RF exposure guidelines require that the device be used at a minimum of 0.5 cm from the human body. Failure to observe this
guideline may result in RF exposure exceeding limits.
■
Certification information (SAR)
This device meets guidelines for exposure to radio waves.
Your device is a low-power radio transmitter and receiver. As recommended by international guidelines, the device is designed
not to exceed the limits for exposure to radio waves. These guidelines were developed by the International Commission on
Non-Ionizing Radiation Protection (ICNIRP), an independent scientific organization, and include safety measures designed to
ensure the safety of all users, regardless of age and health.
The Specific Absorption Rate (SAR) is the unit of measurement for the amount of radio frequency energy absorbed by the body when
using a device. The SAR value is determined at the highest certified power level in laboratory conditions, but the actual SAR level during
operation can be well below the value. This is because the device is designed to use the minimum power required to reach the network.
The SAR limit adopted by Europe is 2.0 W/kg averaged over 10 grams of tissue, and the highest SAR value for this device
complies with this limit.
■
Statement
Hereby, Huawei Technologies Co., Ltd. declares that this device is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU.
The most recent and valid version of the DoC (Declaration of Conformity) can be viewed at
https://consumer.huawei.com/certification.
This device may be operated in all member states of the EU.
Observe national and local regulations where the device is used.
This device may be restricted for use, depending on the local network.
Restrictions in the 2.4 GHz band:
Norway:
This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund.
Restrictions in the 5 GHz band:
WLAN function of this device is restricted only to indoor use when operating in the 5150 to 5350 MHz frequency range.
FCC Regulatory Compliance
■
RF exposure requirements
Important safety information regarding radio frequency (RF) radiation exposure:
RF exposure guidelines require that the device be used at a minimum of 1 cm from the human body. Failure to observe this
guideline may result in RF exposure exceeding limits.
■
Certification information (SAR)
This device is also designed to meet the requirements for exposure to radio waves established by the Federal Communications
Commission (USA).
The SAR limit adopted by the USA is 1.6 W/kg averaged over one gram of tissue.The highest SAR value reported to the FCC for
this device type complies with this limit.
■
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Caution:
Any changes or modifications to this device not expressly approved by Huawei Technologies Co., Ltd. for compliance
could void the user
’
s authority to operate the equipment.
Restrictions in the 5 GHz band:
Within the 5.15 to 5.25 GHz band, UNII devices will be restricted to indoor operations to reduce any potential for harmful
interference to co-channel Mobile Satellite System (MSS) operations.
■
FCC ID
Check FCC ID in the following steps.
“Settings”
→
“About”
→
“Certification”
Export Administration Regulations
The product and its accessories may be subject to the Japan Export Administration Regulations (“Foreign Exchange and Foreign Trade
Law” and its related laws). In addition, U.S. Re-export Regulations (Export Administration Regulations) may apply to the product and
its accessories. To export and re-export the product and its accessories, take the required measures on your responsibility and at your
expenses. For details on the procedures, contact the Ministry of Economy, Trade and Industry or the U.S. Department of Commerce.
Trademarks
• Microsoft
®
, Windows
®
, are trademarks or registered trademarks of Microsoft Corporation in the United States.
• The official name for Windows is Microsoft
®
Windows
®
Operating System.
• Internet Explorer is a trademark or registered trademark of Microsoft Corporation in the United States/other countries.
• Firefox is a registered trademark or trademark of Mozilla Foundation in the United States and/or other countries.
• Google, Android and Google Chrome are trademarks or registered trademark of Google LLC.
• Opera is a trademark or registered trademark of Opera Software ASA. For details about Opera, refer to http://jp.opera.com/.
• Mac, Macintosh, Safari, iPhone, iPod, iPod touch, and iPad are trademarks or registered trademarks of Apple Inc. in the
United States/other countries.
• The trademark “iPhone” is used with a license from AIPHONE CO., LTD.
• Wi-Fi
®
, Wi-Fi Alliance
®
, Wi-Fi CERTIFIED
®
, WPA™, WPA2™, Wi-Fi Protected Setup™ and the logo are trademarks or
registered trademarks of Wi-Fi Alliance.
• USB Type-C™ is a trademark of USB Implementers Forum.
• QR Code is a registered trademark of DENSO WAVE INCORPORATED.
• The Bluetooth word mark and logo are registered trademarks owned by the Bluetooth SIG, INC., and HUAWEI
TECHNOLOGIES is licensed to use these trademarks.
• HUAWEI is a registered trademark or trademark of HUAWEI TECHNOLOGIES CO., LTD. in China.
• Other company names and product names referred to in this manual are trademarks and registered trademarks of respective
companies. The ® marks or TM marks may be omitted in this manual.
Policy on the protection of personal information
Please refer to the websites listed below if you would like more detailed information regarding the HUAWEI TECHNOLOGIES
CO., LTD. policy on the protection of personal information.
https://consumer.huawei.com/minisite/legal/privacy/statement.htm?country=JP&language=ja-JP (Japanese)
January 2019, 1st Edition
Sold by: KDDI CORPORATION, OKINAWA CELLULAR TELEPHONE COMPANY
Imported by: HUAWEI Technologies Japan K.K.
Manufactured by: HUAWEI TECHNOLOGIES CO., LTD.
●
Never use modified the product. Use of a modified device violates the Radio Law and Telecommunications Business Act.
The product obtains a technical standards conformity certification of specified wireless equipment based on the Radio Law
and a technical standards conformity approval based on the Telecommunications Business Act, and as a proof, you can
check the “Technical Conformity Mark ” with the product.
To display the mark, in the Home screen, tap “Settings”
→
“About”
→
“Certification”.
If any modification is made to the internal components, the certification of conformity with technical regulations will become
invalid. Never use the product without the valid certification. Doing so violates the Radio Law and Telecommunications
Business Act.
●
Take care not to place magnetized items such as magnetic cards, speakers and TV sets near the product, as it might
cause a malfunction.
Putting a strong magnetism close to the product might cause false operation.
●
Do not bring magnetized cards such as cash cards, credit cards and pre-paid cards closer to the product. Doing so might
cause loss of the recorded data.
●
When you put the product in your pocket or bag, take care so that the display panel does not come in contact with metal
objects or other hard objects. Doing so might cause scratches or damage. Also, be careful not to scratch or damage the
display panel by using a strap whose metal or other hard part comes in contact with the display panel.
●
When the product is suddenly brought into a warm place from a cold place, or used in a humid place or a place where the
temperature suddenly changes (e.g. near the air discharge port of an air conditioner), water droplets (i.e. condensation)
may be generated inside of the product. Note that if you use the product under such conditions, humidity might cause
corrosion or a malfunction.
●
Use the product with the Nano IC Card slot cover closed. If you use with the Nano IC Card slot cover open, dust or water
might get inside and cause a malfunction.
●
Do not allow liquids, metal objects, or other foreign objects to get inside of the Nano IC Card slot. Doing so might cause a
malfunction.
●
Do not give strong impact on the product such as dropping, throwing, or stomping. Doing so might cause a malfunction.
●
Do not place the product directly on a sandy beach etc. If sand etc. gets inside of the product, it might cause a malfunction.
■
Touch Panel
●
Do not put a sticker, sheet (e.g. commercially available protective film, peep prevention sheet), etc. on the display panel.
Doing so might hinder correct operation of the touch panel.
●
When carrying the product in your pocket or bag, take care not to allow the touch panel to get close to a conductive
material such as metal, as it might cause false operation of the touch panel.
■
Internal Battery
(The internal battery of the product is a lithium-ion battery)
The internal battery is not fully charged at the time of purchase. Charge the battery before using the product.
Charge the battery before using if you have not used the product for a long time.
●
Use of the product in very hot or cold environment, for example, when leaving it in a car with the windows closed in
summer, causes the internal battery capacity to drop and shorten the available battery usage time. That also shortens the
internal battery life. Basically use the product at room temperature.
●
The internal battery gradually discharges after charging even if the product has not been used. The internal battery might
be discharged if you have not used the product for a long time. Charge the product before using.
●
The internal battery is a consumable part. If the performance of a battery does not recover (e.g. the usable time after
each charge has become extremely short), the battery is at the end of service life, so stop use. The battery is built into the
product. For repair, the product must be collected to au shop etc. and charges will be incurred. And you may not use the
product during certain period of time. Please be forewarned. Note that the length of service life varies depending on the
usage condition etc.
●
The internal battery sometimes swells up as it approaches the end of its service life. This is due to property of lithium-ion
batteries, and is not a problem in terms of safety.
■
Charging equipment
●
Do not wrap the cord of the specified charging equipment (sold separately) around the adapter itself. Do not bend
connection part of charging equipment and power plug forcedly. Do not place a heavy object on a cord of adapter or
power cable, or do not apply unreasonable force to the cord such as pulling. Doing so might cause a malfunction.
●
Grasp the power plug of the specified charging equipment when removing from a power outlet. If you pull the cable, the
cable might be damaged.
■
USB Type-C to Micro B adapter (sample)
●
Do not bend the connection part of the connector and the product, a PC, etc. forcedly. Doing so might cause a malfunction.
■
au IC card
●
Do not forcibly remove or insert the au IC card. Be careful not to exert excessive force when inserting the card into the product.
●
You are responsible for any damage caused by inserting your au IC card into some other IC card reader/writer etc.
●
Do not put a sticker etc. on au IC card.
●
Do not insert the au IC card with a conversion adapter attached. Doing so might cause a malfunction.
●
Do not damage the card by using the product in a hot place, dropping into fire, contacting to the metal part with foreign
object, giving an impact, bending, applying load, etc. Doing so might cause loss of data or a malfunction.
■
Copyrights & portrait rights
●
You are not allowed to copy, distribute, publish, modify, or edit the data you downloaded using the product without consent
of the copyright holder, except for personal use, under the copyright law.
In addition, do not use or modify portraits or names of other individuals without the consent, as it might infringe on rights of
portrait.
■
Backup content on the product
●
Please back up important content you registered to the product. Content recorded to the memory of the product might
disappear or be altered by unexpected factors, such as static electricity or a malfunction, repair, mishandling, etc.
Notes on using Bluetooth
®
/Wireless LAN (Wi-Fi
®
) functions
• The Bluetooth
®
function and wireless LAN (Wi-Fi
®
) function of the product conforms to domestic wireless standards in Japan,
FCC standards, and EC directives and obtained the certification.
• Use 5 GHz band wireless LAN (Wi-Fi
®
) function of the product in Japan. The 5 GHz band wireless LAN (Wi-Fi
®
) function of
the product conforms to domestic wireless standards in Japan, and has been certified. Use of it overseas may be subject to
punishment by law.
• Use of Bluetooth
®
function and Wireless LAN (Wi-Fi
®
) function may be restricted in some countries/regions. Before using the
product overseas, check the relevant laws and regulations of the country/region you visit.
• The 2.4 GHz band used by wireless LAN (Wi-Fi
®
) or Bluetooth
®
devices is operated by various other devices. For this reason,
the communication speed or communication range may be decreased, or disconnection of communication may occur, due
to interference by other devices.
• Do not use the product in a place near electric products, AV, OA equipment, or other magnetized devices, or where
electromagnetic waves are generated.
• Subjecting the product to magnetic or electrical noise might increase noise and hinder the communication (particularly when
it used near a microwave oven).
• Using the product near a TV, radio or similar appliance might cause reception interference and disrupt TV images.
• Searching might not be successful if there are multiple wireless LAN (Wi-Fi
®
) access points near the product and they use
the same channel.
• Use of electric devices on board is restricted. Follow the instructions of each airline company.
• The communication speed or communication range vary depending on the distance between communication devices,
obstacles, and connected devices.
Cautions on using 2.4 GHz band
Bluetooth
®
function/Wireless LAN (Wi-Fi
®
) function of the product uses 2.4 GHz band. In this frequency band, other similar
wireless stations, in-plant wireless stations for mobile unit identification that require a license to use, such as factory production
lines, specific small power wireless stations that do not require licenses, amateur wireless stations (collectively called “other
wireless stations” from here on) are operated in addition to home electrical appliances such as microwave ovens, devices for
industrial, scientific and medical devices.
* The product cannot perform connection operation or data communication via Bluetooth
®
function.
1. Before using the product, make sure that “other wireless stations” are not in operation nearby.
2. In the event that instances of radio wave interference have occurred between the product and “other wireless stations”,
immediately either relocate the product or stop operation of the device (stop emission of radio waves).
3. If you are unclear on any points or are troubled by anything, contact an au shop or Customer Service Center.
• Connections between the product and all Bluetooth
®
/wireless LAN (Wi-Fi
®
) devices have not been confirmed. Therefore,
connections with all Bluetooth
®
/wireless LAN (Wi-Fi
®
) devices are not guaranteed.
• The product supports security features for wireless communications that are compliant with the wireless LAN (Wi-Fi
®
)
standard specifications, but the security may not be sufficient depending on the usage environment and configuration. Be
careful when making data communication using wireless LAN (Wi-Fi
®
) function.
• Wireless LAN (Wi-Fi
®
) has the advantage that it can be freely connected anywhere within the radio wave range, as it uses
radio waves for exchanging information. At the same time, there is a risk that a malicious third party may obtain unauthorized
access if security settings have not been configured. You are recommended to configure security settings before using it at
your decision and responsibility.
• The Company assumes no responsibility for leakage of data or information that may occur during wireless LAN (Wi-Fi
®
)
communication.
• Since Bluetooth
®
and wireless LAN (Wi-Fi
®
) functions use the same frequency band, using the both functions at the same
might cause radio wave interference resulting in decreased communication speed or disconnection from the network. If
connection fails, stop using either of the Bluetooth
®
and wireless LAN (Wi-Fi
®
) functions.
Bluetooth
®
function and wireless LAN (Wi-Fi
®
) function of the product use 2.4 GHz band.
2.4DS4/OF4/XX8
• Bluetooth
®
function
The product uses the 2.4 GHz band. XX8 is used as the other modulation scheme. The interference distance is about 80 m or
less. This means that all bandwidths are used, and that bands of mobile unit identification devices can be avoided.
• Wireless LAN (Wi-Fi
®
) function
The product uses the 2.4 GHz band. DS-SS and OFDM are used as the modulation schemes. The interference distance is about
40 m or less. This means that all bandwidths are used, and that bands of mobile unit identification devices can be avoided.
Available channels differ depending on the country.
For use in an airplane, check with the airline company in advance.
Cautions on using 5 GHz band
Wireless LAN (Wi-Fi
®
) function of the product uses 5 GHz band. Using the 5.2 GHz band and 5.3 GHz band outdoors is
prohibited by the Radio Law.
The channels used on the product are as follows.
W52 (5.2 GHz band/36, 40, 44, 48 ch)
W53 (5.3 GHz band/52, 56, 60, 64 ch)
W56 (5.6 GHz band/100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 ch)
