Huawei SMU01A User Manual Download Page 9

Page: 9 / 48

SMU01A
User Manual

1 SMU01A Overview

Issue 06 (2015-10-08)

Huawei Proprietary and Confidential

Category

Function

Detection

Monitors AC input voltages.

Monitors load currents.

Monitors DC busbar voltages.

Monitors battery temperatures.

Monitors ambient humidity.

Monitors ambient temperatures.

Monitors standby analog values.

Control

Resets the smoke sensor remotely. (The smoke sensor can be remotely
reset after an alarm is cleared.)

Provides eight dry contact outputs.

Alarm
reporting

Reports alarms for SMU01A faults.

Reports DC overvoltage alarms.

Reports DC undervoltage alarms.

Reports alarms for abnormal load currents.

Reports alarms for DC ultra overvoltage.

Reports alarms for DC ultra undervoltage.

Reports alarms for mains failure.

Reports alarms for very high ambient temperatures.

Reports alarms for the water sensor.

Reports alarms for the smoke sensor.

Reports alarms for wire frames.

Reports alarms for load fuse blown.

Reports alarms for humidity sensor faults.

Reports alarms for long-time AC failures.

Reports alarms when communication failures of all rectifiers.

Reports alarms for single-rectifier faults. (There is no reserved rectifier.)

Reports alarms for multi-rectifier faults.

Reports alarms for communication failures.

Reports alarms for rectifier faults.

Reports alarms for very high battery temperatures.

Reports alarms for very low battery temperatures.

Summary of Contents for SMU01A

















































Search results

Summary of Contents for SMU01A

Reviews:

Related manuals for SMU01A

Brands by name

Popular brands

Huawei SMU01A, User Manual

Search results

Summary of Contents for SMU01A

Reviews:

Related manuals for SMU01A

Brands by name

Popular brands