Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 49 / 553

background image

NOTE

l

The IP address is the management IP address of the MA5616.

l

Select the SNMP parameters based on the selected SNMP version. This section
considers the SNMP V2c default profile as an example. You can select the profile
corresponds to the actual planning.

c.

Click

OK

. Several seconds to some 10 minutes are required for uploading the

device data. After reading the related data, the system automatically updates the
device icon.

----End

Result

You can maintain and manage the MA5616 through the U2000.

Configuration File

The following part provides the script for configuring the outband NMS (on the device).

snmp-agent community read public
snmp-agent community write private
snmp-agent sys-info contact HW-075528780808
snmp-agent sys-info location Shenzhen_China
snmp-agent sys-info version v2c
snmp-agent trap enable standard
snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC
snmp-agent target-host trap-paramsname ABC v2c securityname private
snmp-agent trap source meth 0
save

The following part provides the script for configuring the inband NMS (on the device). The
management VLAN ID of the upstream port is 30.

snmp-agent community read public
snmp-agent community write private
snmp-agent sys-info contact HW-075528780808
snmp-agent sys-info location Shenzhen_China
snmp-agent sys-info version v2c
snmp-agent trap enable standard
snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC
snmp-agent target-host trap-paramsname ABC v2c securityname private
snmp-agent trap source vlanif 30
save

3.2.3 Configuring the U2000 (Based on SNMPv3)

When SNMPv3 is used, the MA5616 can be interconnected with the U2000 in inband or outband
networking mode.

Prerequisites

l

If the device is interconnected with the NMS in outband networking mode, the
communication port (maintenance network port) must be configured. For detailed
procedure, see

3.1.2 Configuring Outband Management

l

If the device is interconnected with the NMS through the PON upstream port in inband
networking mode, the communication port (PON upstream port) must be configured. For
detailed procedure, see

3.1.3 Configuring Inband Management (GPON Upstream)

.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

38

«
...
47
48
49
50
51
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: EAW Pages: 10

Brand: Accelerated Pages: 10

Brand: Accelerated Pages: 4

Brand: Javad Pages: 35

Magic WiFi mini Ek

Brand: Devolo Pages: 22

ION 1200 Series

Brand: PaloAlto Networks Pages: 90

Brand: Davey Pages: 18

Brand: Telex Communications Pages: 28

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

Brand: Advantech Pages: 36

Brand: BHU NETWORKS Pages: 75

REJ06B0734-0100

Brand: Renesas Pages: 19

Brand: Aaeon Pages: 57

Brand: Juniper Pages: 196

Brand: ZALMAN Pages: 18

Brand: Procool Pages: 2

Brand: AC Infinity Pages: 24

Brand: swiftech Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands