Huawei SmartAX MA5616 Configuration Manual Download

Page: 33 / 553

If the remote WAN management environment is set up as shown in

Figure 3-10

, run the

route-static

command to add a route to the next hop.

huawei(config-if-meth0)#

quit

huawei(config)#

ip route-static 10.10.21.0 24 10.10.20.254

Step 4

Start Telnet on the maintenance terminal.

Choose

Start

Run

on the maintenance terminal. In the

Open

address bar, enter

telnet

10.10.20.2

(10.10.20.2 is the IP address of the maintenance Ethernet port of the MA5616), as

shown in

Figure 3-12

(considering the Windows OS as an example). Click

, and the telnet

interface is displayed.

Figure 3-12

Starting Telnet

Step 5

On the telnet interface, enter the user name and the password. By default, the super user name
is

root

and the password is

mduadmin

. When the login is successful, the system displays the

following information:

>>User name:

root

>>User password:


Huawei Integrated Access Software (MA5616).

Copyright(C) Huawei Technologies Co., Ltd. 2002-2010. All rights reserved.

----End

Result

After logging in to the MA5616, you can manage the MA5616. For instructions on CLI, see CLI
Operation Characteristics.

3.1.3 Configuring Inband Management (GPON Upstream)

This topic describes how to log in to the MA5616 through an OLT from the maintenance terminal
to manage the MA5616.

Prerequisites

The physical connection between the MA5616 and the OLT must be normal.

The IP address of the maintenance terminal must be properly configured.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands