Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 31 / 553

background image

Figure 3-10

Example network for configuring outband management over a WAN in the telnet

mode

PC

PC

PC

LAN

Router

MA5616

In this example network, the MA5616 is connected to the WAN through the maintenance
Ethernet port. You can manage the MA5616 remotely from the maintenance terminal.

Data Plan - WAN

provides the data plan for configuring outband management over a WAN in the telnet

mode.

Table 3-2

Data plan for configuring outband management over a WAN in the telnet mode

Item

Data

Maintenance Ethernet port of the
MA5616

IP address: 10.10.20.2/24

Ethernet port of the maintenance
terminal

IP address: 10.10.21.3/24

Port of the router connected to the
MA5616

IP address: 10.10.20.254/24

Configuration Flowchart

Figure 3-11

shows the flowchart for outband management in the telnet mode.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

20

«
...
29
30
31
32
33
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: E-Lins Pages: 59

Brand: E-Lins Pages: 11

Brand: E-Lins Pages: 9

Brand: E-Lins Pages: 5

Network Video Recorders

Brand: e-Line Technology Pages: 34

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 16

Brand: Patton electronics Pages: 51

Brand: Profile Pages: 6

DM/IP601-CPCI-100BT

Brand: Dialogic Pages: 2

Brand: Idis Pages: 31

Brand: Davey Pages: 18

Brand: protech Pages: 95

Brand: Juniper Pages: 2

Brand: Techroutes Pages: 20

CNPS7000A Series

Brand: ZALMAN Pages: 9

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Brand: Intel Pages: 112

Brand: Supermicro Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands