manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

l

IUA interface ID: 0 (value of 

iid-map

: 1)

l

Terminal ID: 2 (not supporting the terminal layering function)

l

User priority: cat3

l

Telephone number: 83110001 (Before configuring a emergency standalone number, ensure
that the emergency standalone function has been enabled on the MG interface. For details,
see 

7.3.1.5 (Optional) Configuring the Software Parameters of an MG Interface

.)

l

UNI alarm report function: enable

l

Threshold for the number of auto recoveries from L1 deterioration faults: 30

To add an ISDN BRA user with such configurations on port 0/4/0 of MG interface 0, do as
follows:

huawei(config-sigtran)#

quit

huawei(config)#

esl user

huawei(config-esl-user)#

mgbrauser add 0/4/0 0 0 interfaceid 0 terminalid 2 prior

ity cat3 telno 83110001

 Are you sure to configure the working mode of the DSL board to normal and reset
 the board automatically? (y/n)
[n]:

y

                                                         

huawei(config-esl-user)#

display mgbrauser 0/4

  ------------------------------------------------------------------------------
  F  /S /P /B  MGID     LinkSetNo UserIFID TelNo            Priority TerminalID
  ------------------------------------------------------------------------------
  0  /4 /0 /0  0        0         0        83110001         Cat3     A2
  ------------------------------------------------------------------------------
huawei(config-esl-user)#

mgbrauser attribute set 0/4/0 priority cat3 unireport 

enable auto-resume-limit 30

huawei(config-esl-user)#

display mgbrauser attribute 0/4/0

{ <cr>|endframeid/slotid/portid<S><Length 1-15> }:                              
                                                                                
  Command:                                                                      
          display mgbrauser attribute 0/4/0                                     
  --------------------------------------------------------
  F  /S /P  UNIreport  Prior  Auto-reservice-times/limit
  --------------------------------------------------------
  0  /4 /0  enable     Cat3   0/30
  --------------------------------------------------------

7.3.3.2 (Optional) Configuring the System Parameters

This topic describes how to configure the system parameters including the overseas version flag
and message waiting indication (MWI) mode according to the local standards to ensure that the
response of the user terminal complies with the local standards.

Context

Table 7-25

 lists the system parameters supported by the MA5616.

Table 7-25

 System parameters supported by the MA5616

Parameter

Description

Default Setting

0

Indicates the howler tone
sending flag.

1: Indicates that the howler tone
is sent.

1

Indicates the overseas version
flag.

0: Indicates China.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

293

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

D-Link DSL-504T Manual preview
DSL-504T
Brand: D-Link Pages: 99
D-Link DI-804V Datasheet preview
DI-804V
Brand: D-Link Pages: 5
D-Link DES-1210-08P Manual preview
DES-1210-08P
Brand: D-Link Pages: 15
D-Link AirPro DWL-6000AP Manual preview
AirPro DWL-6000AP
Brand: D-Link Pages: 65
D-Link GO-RT-N300 Quick Installation Manual preview
GO-RT-N300
Brand: D-Link Pages: 32
D-Link DXN-W224 Quick Start Manual preview
DXN-W224
Brand: D-Link Pages: 6
D-Link DSR-250N User Manual preview
DSR-250N
Brand: D-Link Pages: 221
D-Link Express Ethernetwork DI-707P Quick Installation Manual preview
Express Ethernetwork DI-707P
Brand: D-Link Pages: 14
4RF Aprisa LTE Quick Start Manual preview
Aprisa LTE
Brand: 4RF Pages: 7
JB Systems Scene Master Operation Manual preview
Scene Master
Brand: JB Systems Pages: 24
JB Systems CMX 24 User Manual preview
CMX 24
Brand: JB Systems Pages: 61
Paradyne MCC Installation Instructions Manual preview
MCC
Brand: Paradyne Pages: 11
Paradyne Hotwire 8784 Installation Instructions Manual preview
Hotwire 8784
Brand: Paradyne Pages: 19
Paradyne Hotwire 7995 Installation Instructions Manual preview
Hotwire 7995
Brand: Paradyne Pages: 32
Paradyne COMSPHERE 3550 Series User Manual preview
COMSPHERE 3550 Series
Brand: Paradyne Pages: 153
Paradyne Jetstream CPX-1000 Reference Manual preview
Jetstream CPX-1000
Brand: Paradyne Pages: 141
Paradyne FrameSaver 9783 Installation Instructions Manual preview
FrameSaver 9783
Brand: Paradyne Pages: 28
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Brand: M86 Security Pages: 46

Brands by name

Popular brands

Load more brands