manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

Step 4

Check whether the configuration of the digitmap timer is the same as that in the data plan.

l

Run the 

display digitmap

 command to check whether the digitmap is configured correctly.

l

Run the 

display digitmap-timer

 command to check whether the digitmap timer is configured

correctly.

----End

Example

Assume that the inner digitmap of the H.248-based MG interface is configured. According to
the data plan, the inner digitmap format is 1234xxxx. The digitmap timer is not configured
because it is issued by the MGC. To configure the inner digitmap, do as follows:

huawei(config)#

interface h248 0

huawei(config-if-h248-0)#

digitmap set inner 1234xxxx

huawei(config-if-h248-0)#

display digitmap

                                       

  ---------------------------------------------------------------------- 
  Inner digitmap                                          : 1234xxxx   
  Urgent digitmap (for overload or bandwidth restrict)    : -        
  Dualdial digitmap for card service                      : -       
  ----------------------------------------------------------------------

7.3.1.5 (Optional) Configuring the Software Parameters of an MG Interface

The software parameters of an MG interface mainly define certain common service attributes
of the MG interface. After the configuration of the software parameters of an MG interface, the
software parameters take effect immediately and the configuration is valid only to the MG
interface.

Context

There are 36 software parameters (numbered from 0 to 35) of an MG interface that supports H.
248. 

Table 7-23

 lists the configurable parameters, and the other parameters are reserved in the

system.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

276

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Brand: Baracoda Pages: 42
Lauterbach C2000 Manual preview
C2000
Brand: Lauterbach Pages: 61
Paradyne FrameSaver 9120 Installation Instruction Supplement preview
FrameSaver 9120
Brand: Paradyne Pages: 2
TP-Link tl-wr845n Quick Installation Manual preview
tl-wr845n
Brand: TP-Link Pages: 2
ESD ECS-CPCIs/FPGA Hardware Manual preview
ECS-CPCIs/FPGA
Brand: ESD Pages: 28
Speedtouch IPQoS Configuration Manual preview
IPQoS
Brand: Speedtouch Pages: 124
Garland INT40G2SR44 User Manual preview
INT40G2SR44
Brand: Garland Pages: 43
NC-link NC-AP111 User Manual preview
NC-AP111
Brand: NC-link Pages: 20
Cabletron Systems MMAC-Plus 9G536-04 User Manual preview
MMAC-Plus 9G536-04
Brand: Cabletron Systems Pages: 42
Supermicro AOC-STG-I2 User Manual preview
AOC-STG-I2
Brand: Supermicro Pages: 15
NETGEAR RBRE960B User Manual preview
RBRE960B
Brand: NETGEAR Pages: 152
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2
ENERMAX ELC-LMT120-RGB User Manual preview
ELC-LMT120-RGB
Brand: ENERMAX Pages: 33
ADLINK Technology VPX3000 Series Manual preview
VPX3000 Series
Brand: ADLINK Technology Pages: 95
Harman Lexicon MPX 200 User Manual preview
Lexicon MPX 200
Brand: Harman Pages: 77
Nexus OSL101 Instructions Manual preview
OSL101
Brand: Nexus Pages: 9
ZyXEL Communications Dimension GS-2024 User Manual preview
Dimension GS-2024
Brand: ZyXEL Communications Pages: 266
Patton electronics SmartNode 4634 Series Quick Start Manual preview
SmartNode 4634 Series
Brand: Patton electronics Pages: 12

Brands by name

Popular brands

Load more brands