Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 21 / 553

background image

3

Basic Configuration

About This Chapter

This topic describes how to perform the basic configuration, including common configuration,
public configuration, and service preconfiguration. These types of configurations do not have
definite logic relations between each other. Therefore, you can perform the configuration based
on actual requirements.

3.1 Configuring the Maintenance Terminal

This topic describes three modes of managing the MA5616 from the maintenance terminal.

3.2 Configuring the U2000

The MA5616 can be interconnected with Huawei iManager U2000 (hereinafter referred to as
U2000). Hence, the administrator can maintain and manage the device through the U2000. The
MA5616 can be interconnected with the U2000 in inband or outband networking mode. The
following part describes how to configure the inband networking and outband networking based
on SNMP V1, SNMP V2c, and SNMP V3 respectively.

3.3 Configuring the Attributes of the Upstream Port

The MA5616 can be interconnected with the OLT through upstream GPON/GE port. This topic
describes how to configure the attributes of upstream GPON/GE port so that the device
communicates successfully with the upstream device.

3.4 Configuring the Link Aggregation of Upstream Ethernet Port

Port aggregation means aggregating the two upstream GE ports of the MA5616 to increase the
bandwidth through load balancing. When a certain aggregated GE port or GE link fails, data is
transmitted through another GE port. Thus, the reliability of the transmission is enhanced.

3.5 Configuring the ANCP

Access Node Control Protocol (ANCP) is used to implement the functions such as topology
discovery, line configuration, and Layer 2 Control (L2C) OAM on the user ports. The
MA5616 establishes an ANCP session according to the communication IP address of the General
Switch Management Protocol (GSMP) that is used by the network access server (NAS).

3.6 Configuring a VLAN

Configuring VLAN is a prerequisite for configuring a service. Hence, before configuring a
service, make sure that the VLAN configuration based on planning is complete.

3.7 Configuring the xDSL Profile

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

10

«
...
19
20
21
22
23
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

SmartSwitch Router

Brand: Cabletron Systems Pages: 338

Brand: A10 Pages: 52

Brand: Industrex Pages: 51

Brand: Idis Pages: 31

Brand: Patton electronics Pages: 65

Brand: Winext Pages: 37

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

Brand: SurfControl Pages: 2

Brand: Lanner Pages: 59

MMAC-Plus 9G536-04

Brand: Cabletron Systems Pages: 42

Brand: iDirect Pages: 72

Brand: Omron Pages: 29

Brand: NetCommWireless Pages: 28

OPTIMA II CNPS10X

Brand: ZALMAN Pages: 20

Brand: Airlinkplus Pages: 24

Brand: Atlantis Land Pages: 2

Brand: NovaStar Pages: 16

Brand: Behringer Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands