Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 60 / 553

background image

Run the

display link-aggregation all

command to query the type, number and working mode

of the aggregated Ethernet ports.

----End

Result

In ETH mode, the PC can still access the Internet through PPPoE dialup after you run the

shutdown

command to deactivate port 0/0/0 or 0/0/1.

Example

Assume that two upstream ports 0/0/0 and 0/0/1 on the same CCUC board of the MA5616 is to
be configured as an aggregation group, and each port sends packets according to the source MAC
address in the static LACP aggregation mode. To perform the preceding configuration, do as
follows:

huawei(config)#

link-aggregation 0/0 0-1 ingress workmode lacp-static

huawei(config)#

display link-aggregation all

-------------------------------------------------------------------------
Master port Link aggregation mode Port NUM Work mode Max link number
-------------------------------------------------------------------------
0/0/0 ingress 2 lacp-static -
-------------------------------------------------------------------------
Total: 1 link aggregation(s)

3.5 Configuring the ANCP

Access Node Control Protocol (ANCP) is used to implement the functions such as topology
discovery, line configuration, and Layer 2 Control (L2C) OAM on the user ports. The
MA5616 establishes an ANCP session according to the communication IP address of the General
Switch Management Protocol (GSMP) that is used by the network access server (NAS).

Context

l

The MA5616 and the NAS use the TCP connection to carry an ANCP session. Therefore,
before creating the ANCP session, you must create a TCP connection between the
MA5616 and the NAS. The NAS functions as the server of the TCP connection, and the
MA5616 functions as the client of the TCP connection.

l

After the TCP connection is created successfully between the MA5616 and the NAS, an
ANCP session is created between the MA5616 and the NAS. After the ANCP session is
created successfully, the MA5616 and the NAS need to use the ANCP ACK packets for
heartbeat detection to maintain the ANCP session.

l

The default values of the ANCP parameters are as follows:

–

GSMP communication IP address for an ANCP session: 0.0.0.0

–

ANCP session capability set: topology-discovery, line-config, and oam

–

ANCP packet sending priority: 6

–

GSMP TCP communication port ID on the NAS side in an ANCP session: 6068

–

Interval for sending packets during the initial stage of an ANCP session: 10 (unit: 0.1s)

–

Interval for sending packets during the ANCP session stage: 100 (unit: 0.1s)

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

49

«
...
58
59
60
61
62
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Makita Pages: 2

Elinx EIRP305-T

Brand: B&B Electronics Pages: 19

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Fieldbus Specialists Pages: 39

Brand: Keithley Pages: 71

Brand: TP-Link Pages: 87

DataPlot CB1224

Brand: B-G Instruments Pages: 4

XC-16CH-NVR-4TB

Brand: Xyclop Pages: 19

Brand: Patton electronics Pages: 8

Brand: LevelOne Pages: 49

Brand: AMD Pages: 27

Brand: EXAGATE Pages: 7

Brand: Extron electronics Pages: 19

Brand: WTI Pages: 178

Brand: Airlinkplus Pages: 24

Brand: Vivotek Pages: 13

Brand: Garner Pages: 13

Brand: Tripp Lite Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands