Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 188 / 553

background image

6.1 Default Settings of the Multicast Service

This topic provides the default settings of the multicast service in the system, including the
configuration of multicast protocol, IGMP version, program configuration mode, bandwidth
management, program preview, and log function.

lists the default settings of the multicast service of the MA5616.

Table 6-1

Default settings of the multicast service

Feature

Default Setting

Multicast protocol

Off

IGMP version

V3

Configuration mode of the multicast
program

Configured statically

Multicast bandwidth management

Enabled

Multicast preview

Enabled

Multicast log function

Enabled

6.2 Configuring the Multicast Service on a Single-NE
Network

This topic describes how to configure the multicast service on a standalone MA5616.

Service Requirements

The multicast function of the MA5616 is used for multicast video services, such as live TV and
near-video on demand (NVOD). The MA5616 runs the IGMP proxy or IGMP snooping protocol,
and the interconnected device can run the IGMP proxy, IGMP snooping, or multicast router
protocol.

Currently, the multicast application of the MA5616 is oriented to L2, and the MA5616 forwards
data based on VLAN ID + multicast MAC address. A multicast program on the network is
uniquely identified by VLAN ID + multicast IP address. The MA5616 differentiates multicast
sources by VLAN ID. It allocates a unique VLAN ID to each multicast source, controls the
multicast domain and user rights based on the multicast VLAN ID, and provides a platform for
different ISPs to implement different multicast video services.

Prerequisite

The license for the multicast program or multicast user must be applied for and installed.

Data Plan

Before configuring the multicast video service, plan the data items as listed in

.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

6 Configuring the Multicast Service (Multicast VLAN Mode)

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

177

«
...
186
187
188
189
190
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: QNAP Pages: 20

Brand: Ubee Pages: 9

Brand: TP-Link Pages: 73

Brand: Compaq Pages: 112

RouterBOARD SXT 5HnD

Brand: MikroTik Pages: 2

Scorpio WD2500BPVT

Brand: Western Digital Pages: 3

Scorpio WD2500BPVT

Brand: Western Digital Pages: 4

Storagelibrary T24

Brand: Tandberg Data Pages: 28

Brand: UNA AUTOMATION Pages: 20

Brand: SIIG Pages: 20

SLK-R602 Series

Brand: Seriallink Pages: 29

Brand: AXAGO Pages: 2

Brand: Renesas Pages: 76

Serial Attached SCSI (SAS) Expander Card

Brand: Adaptec Pages: 26

Brand: Renesas Pages: 4

Brand: Inspired Energy Pages: 5

Brand: COUGAR Pages: 2

Brand: Sharedband Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands