Huawei RRU3942 Installation Manual Download Page 53

Page: 53 / 98

Figure 6-29

Top view of the RRU

(1) Angle steel

Procedure

Step 1

Determine a position for installing the main mounting bracket.

If the RRU must be installed on a tower, see

3.5.1 Installation Clearance for a Single

RRU

to determine a position.

If the RRU must be installed on the ground, see

Figure 6-30

to determine a position.

Figure 6-30

Distance between the main mounting bracket and the ground

NOTE

It is recommended that the main mounting bracket be 1,200 mm (47.24 in.) to 1,600 mm (62.99 in.)
above the ground.

Step 2

Fit one end of the auxiliary mounting bracket to one dual-nut bolt assembly of the main mounting
bracket.

Step 3

Install the bracket assembly on angle steel, and then fit the other end of the auxiliary mounting
bracket to the other dual-nut bolt assembly, as shown in

Figure 6-31

RRU3942
Installation Guide

6 Installing the RRU

Issue ()

Huawei Proprietary and Confidential

Summary of Contents for RRU3942



































































































Search results

Summary of Contents for RRU3942

Reviews:

Related manuals for RRU3942

Brands by name

Popular brands

Huawei RRU3942, Installation Manual

Search results

Summary of Contents for RRU3942

Reviews:

Related manuals for RRU3942

Brands by name

Popular brands