Huawei RRU3642 Installation Manual Download Page 61

Page: 61 / 130

7.2.1 Installing a Single RRU

This section describes the procedure and precautions for installing a single RRU on a pole. A
single RRU can be installed on a pole in standard or side-mounted mode.

Prerequisites

Before you install an RRU on a tower, the RRU and mounting brackets are hoisted onto the
tower. For details, see

6.1 Hoisting an RRU onto a Tower

The hoist clamp on the main bracket is secured properly.

NOTICE

Do not stand the RRU upright because the RF ports cannot support the weight of the RRU.

Place a foam pad or cardboard under the RRU to protect the RRU housing from damage
during the installation.

Procedure

Step 1

Determine a position for installing the mounting bracket.

If the RRU must be installed on a pole secured on a tower, see

3.5.1 Clearance for a Single

RRU

to determine a position.

If the RRU must be installed on a pole secured on the ground, see

Figure 7-3

to determine

a position.

Figure 7-3

Distance between the mounting bracket and the ground

NOTE

It is recommended that the mounting bracket be 1,200 mm (47.24 in.) to 1,600 mm (62.99 in.) above
the ground.

Step 2

Loosen the two M10 nuts on the mounting brackets and move the M10x150 bolt out of the trough
on the auxiliary bracket, as shown in

Figure 7-4

RRU3942&RRU3642
Installation Guide

7 Installing the RRU

Issue 07 (2013-12-30)

Huawei Proprietary and Confidential

Summary of Contents for RRU3642



































































































































Search results

Summary of Contents for RRU3642

Reviews:

Related manuals for RRU3642

Brands by name

Popular brands

Huawei RRU3642, Installation Manual

Search results

Summary of Contents for RRU3642

Reviews:

Related manuals for RRU3642

Brands by name

Popular brands