Huawei RRU3232 Installation Manual Download Page 25 | Manualshive

Page: 25 / 95

background image

NOTE

The recommended installation clearance ensures normal running and provides an appropriate space for
Operation and Maintenance (O&M). If there is sufficient space, leave the recommended installation
clearance.
The minimum installation clearance ensures normal running and heat dissipation, but OM activities such
as checking indicator status and opening the maintenance cavity cannot be properly conducted. If the
installation space is restricted, leave the minimum installation clearance.

3.5.1 Installation Clearance for a Single RRU

This section describes the recommended and minimum installation clearance for a single RRU.

Recommended Installation Clearance for a Single RRU

Figure 3-13

shows the recommended installation clearance for a single RRU.

Figure 3-13

Recommended installation clearance for a single RRU

Minimum Installation Clearance for a Single RRU

Figure 3-14

shows the minimum installation clearance for a single RRU.

RRU3232
Installation Guide

3 Information About the Installation

Issue 05 (2011-10-20)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

17

«
...
23
24
25
26
27
...
»

Summary of Contents for RRU3232
































































































Reviews:

No comments

Related manuals for RRU3232

Brand: Canon Pages: 14

IMAGE STABILIZER EF70-200MM F/4L IS USM

Brand: Canon Pages: 13

TIMER REMOTE CONTROLLER TC-80N3

Brand: Canon Pages: 3

TIMER REMOTE CONTROLLER TC-80N3

Brand: Canon Pages: 2

EF-S55-250mm f/4-5.6 IS II

Brand: Canon Pages: 7

Brand: D-Link Pages: 2

Brand: Abibird Pages: 2

Brand: Abicor Binzel Pages: 20

Brand: Lantus Pages: 5

Brand: yasuni Pages: 11

Brand: Raven Pages: 70

DS-KABD8003-RS3

Brand: HIKVISION Pages: 3

Brand: Fisher-Price Pages: 8

Brand: Whispbar Pages: 15

Brand: FORM FIT Pages: 2

Edge Flush Rail

Brand: Thule Pages: 12

Brand: Dynojet Pages: 2

Brand: Ultrak Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands